Search results for query: *

Hi, Does anyone know the command to force a router to retry getting an IP for an dynamic ADSL connection? Thanks Ian

Hi, I have a native Exchange 2003 environment of 5 remote sites all running exchange 2003. I want to create 5 admin groups - each with their own server in. I can do this, but how do you move servers out of the first admin group to a new admin group??? Ian

Hi, I have a 1721 with an ADSL and Serial WIC in it, now, I use route-maps to direct certain types of traffic to certain interfaces - but FTP is killing me. I want all FTP traffic to go out through ADSL, I have allowed the following access-lists: permit tcp any any eq ftp permit tcp any any...

Hi, Does anyone here use any WAN bandwidth monitoring software that can tell a person the tpes of traffic - eg smtp, www, pop3, etc; and the portion of badwidth that certail IP's are using for the WAN links that Cisco routers are connected to? Regards Ian Van Dyk

Hi, I get the following list of errors when I view the debug atm events on my 1751 router - any ideas? 00:06:32: DSL: Open failed: Error in early non-CRC message or in first CRC-cover ed message -- retrying 00:06:32: DSL: Send ADSL_CLOSE command. 00:06:32: DSL: Send ADSL_OPEN command...

Hi Lyndon, Will do, mail me your config: vandyki@vke.co.za What country are you in? Ian

Are you sure that they are using chap for authentication, just include the following in your config incase that are using pap: ppp pap sent-username xxxxx password xxxx And take out your: ppp authentication chap callin statement. Also include the following under global mode: ip cef vpdn...

Sorry to diverge, but I have the same thing basically, how do you inject a route into the routing table, and how do you clear the routing table? Ian

Hi, I just have noticed one problem now, with FTP traffic, the initial connection gets made on port 21, but then the connection dies from internal users to external ftp sites, does it have something to do with the permit tcp any any established rule? Ian

Thanks for that, will give it a try, however, should I put the inbound rule on the ATM interface as you suggest, or on the Dialer interface? Ian

Hi, Please could someone offer some advice: I have a 1721 with three interfaces; an ethernet (10.1.2.1); an adsl (with negotiated ip address - dynamic); and a serial (196.7.0.138). Now, I want to use the ADSL interface for internet access for my company; i.e. traffic from the ethernet to the...

Thanks for the help Andy, I see that it is working fine now, I was just concerned because I have some bandwidth monitoring software that reported very strange figures when I applied the route-maps, but I have found that it was from the large volume of smtp traffic we have - 80% of all our...

Thanks for that info, all of the access-lists have matches against them, however, how do I start all the matches from 0 again, so I can see - i.e. some of them have like 80 000 matches etc.... Also you will notice with an adsl connection, you have atm0, atm0.1 and dialer1 interfaces, which is...

Hi, I have a 1721 with an adsl interface, a 128k serial interface and a fast ethernet interface. I would like to split my outbound traffic in the following way: 1) smtp and pop3 route to the serial interface 2) all other traffic to the adsl interface. I have tried to use route-maps with acls...

Hi, My mistake, I did find the correct speed at 19200 - thanks for the help! Ian

Just a question about your config - what does "ip cef policy" mean? Ian

Hi, Thanks for that, I also thought of that, and still after trying all the speeds can not get a good connection out of it, they all show garbage, do you have a document of exactly what the config registers are - i.e what exactly does 0x2161 do? Ian

Hi, I would like to know how a 1721 load balances two static 0.0.0.0 0.0.0.0 routes? Does it switch between them depending on bandwidth usage? Ian

Hi, I have changed my boot register on a 1750 router to: 0x2161 by mistake, now when the router boots, and I connect to it via console, I just get garbage coming back to me? How can I resolve this?