Search results for query: *

CM 6.0 with Application Enablement Server, also a CS1K 7.5 in the mix. Moving the operators off the 2250's to CM. Anyone running Smart Console on CM? Amcom has been less than impressive with the front end design/build for my side. Any advice or thoughts would be greatly appreciated!!

I have recently installed a new PRI for an Ascom connection and it is built to spec per the guide they sent me. When I dial internal or 9+7 digits I get a double call. For example when 4 digit dialing my desk from Ascom handset my main line and roll over line ring with the call. D-channel...

I have eliminated the CSU and circuit works great. This a point to point CS1K to Option 11, is a CSU expected as best practice by Nortel? I tried everything including as new CSU and cables but the circuit will not come up with it in place! This is driving me nuts! Thanks gys.

ATT shows it up. The channels cycle between dsbl and mnbsy when it's trying to come up if that means anything.

We lost power to the CSU on the Opt 11 end. After ATT tested last night I moved the CSU to a new UPS and it took 20-25 minutes to come back. I did RCNT several times on both ends with no effect.

Once it is up it runs error free. I am clocking off ATT on both ends and no other circuit on either end has problems. Nothing changed in programming since upgrade last Nov. but this seems to be getting worse and taking longer to come up.

I have a PRI between a CS1000m and an Option 11. In the last 3-4 months when it goes down it takes 20 minutes or longer to come back up. Telco has tested to csu on both ends and say it's clean, I have replaced TMDI card and CSU and all cables on the Opt 11 end. Next step is dual pri card on...

I am getting the ERR193 "invalid ntp table". I am suspect that some network routing changes were made without notification. I cannot print or stat ntp in ld 117 it gives me the same ERR193 message. This is my only switch with any network connectivity so I am not too keen on it yet. Shouldn't...

MG1010 branch cabinet off a CS1000M rls 7.0 When a VOIP phone is forwarded outside and called from the CS1000M there is a squeal as the call is connected. If called from a phone registered on the MG1010 cabinet the call is clear.

Connects but no activity. I have changed speeds, etc. Using Procomm and Win7 works for other locations with SEB's but can't get the Opt 11 to do anything.

I have a new usb modem USR 5633 and now I cannot connect to my option 11's with old sportster modems. Any ideas? Thanks.

Thanks johnpoole.....RCAP is set to COLP already so do you think an MSDL download is the fix?

I have a PRI I want to show main number for outbound calls. I have turned on msgo for the d-channel and don't see the number going out, here is all the programming. Thanks TYPE RDB CUST 00 ROUT 50 DES LOOP 14 TKTP DID NPID_TBL_NUM 0 SAT NO RCLS EXT VTRK NO DTRK YES BRIP NO DGTP PRI ISDN...

That is where I think I am with this. Need to change the trunks and route to TIE. Problem is far end needs to stay PRI and NI-2 and I can't provide that, it would have to go to Q-Sig. I think. If anyone knows a way around that let me know please. Thanks

Here is what I see coming my way, all 7 digits plus the 9 are there. DCH 10 UIPE_IMSG CC_SETUP_IND REF 00000900 CH 120 15 TOD 10:13:28 CALLED #:94857505 NUM PLAN: UNKNOWN CALLING #:41398 NUM PLAN: UNKNOWN I have a couple otion 11's that call out using TIE back to me and all is good. This...

Far end is telling me he is inserting a 9 and then sending all 7 digits. My extension on the local switch is 7505 and if far end dials 9 xxx-7505 they end up at my phone.

Want to confirm DMI on a route only affects outbound calls? I have a PRI between two switches (my Nortel and a Seimens). I strip digits and send only 5 to them and that works great. I am having trouble allowing them to send me 9+7 to make local calls out my switch. Seems I'm just getting the...

Does the DMI on a route affect calls in both directions? I want to strip all the digits and insert what I want as calls leave my switch but want to see all digits coming back to me so I can send them out as a local call. (PRI between two swithes) Thanks in advance.

Any problem with running the routines during the day 1 time to capture output for a report? Option 81c rls 25.30

I want to route a number over a PRI to a system and have it show the same caller id info regardless of who calls the number. Example: I want anyone to be able dial 4567 and have it show the same 4 digits across the PRI to the system every call. The system is looking for a DNIS to start a...