Search results for query: *

Hey guys Just wanted to say that I passed the ICND with a score of 934!!! I came in there pretty confident but I have to say that there were some questions there that stumped me. I even had about 15 minutes left when I finished answering question #40. It was funny because I got to the testing...

Dan, Someone will eventually tell you this but you should start your own thread instead of piggybacking on this one. There said it. But yeah I feel your pain my friend. I took the 2 part ccna and had to take the intro 2x to finally pass. I then took the icnd 2x and failed it. Getting ready...

Burt, Here are the other 2 routers. I dont have time to go through the sim to get the whole config but here are the router ip's RouterB E0: 192.168.34.1 /24 S0: 192.168.100.10 /30 Connects to RouterC S1 S1: 192.168.100.6 /30 Connects to RouterA S0 Ospf set to area 0 RouterC E0: 192.168.35.1...

Thanks lerdalt, Just like you I thought the mask was fine using either 0.0.0.0 or 0.0.0.255. I know that 0.0.0.0 is more specific and if I used 0.0.0.255 it would cover anything in that range. I think it is this exam sim that i am using. It seems like they wrote the result with one possible...

Guys I am going to be sitting the ICND here pretty soon and was running through some exam sims and ran into a problem configuring ospf. I finally got it but my question is will any of the ways that the Sybex book by Todd Lammle explained on how to configure ospf work on the ICND? For example...

Congrat's Joey, I hope that in the next few weeks you guys will be seeing me post my successful completion of the ICND. Hey Joey would it be too much to ask what your test consisted of? The last 2 times I took the icnd it seemed to focus on OSPF, EIGRP. How many sims? Were they asking you...

You know what I think I know why they did it that way. the acl that I suggest is only for the s1 interface but allow anything else and if I tried to telnet to that one (s1) the acl will block it but if I tried to telnet to e0 still using the acl that I suggest above I should be able to get...

Hello here is a question that I have. I hopefully did not miss anything and sorry for the diagram (It is missing switch just being lazy): (Lab A)s0(dce)---s1(dte)(Lab b)s0(dce)---(s1(dte)(Lab C) |e0 |e0 |e0 [PC] [Pc] [PC] lab a: Name Dallas...

kade714, I know how you feel. Going into that exam is very tough to say the least. I know I took the icnd 2x and now am concidering taking the single. But anyways I think we may have had the same sim here is a link to my post if you care to take a look...

lerdalt, Thanks for your response, I am going over some online review questions and I dont remember exactly the question but it was something along the lines of "If you were running eigrp/ospf (not sure which one the question was asking) where will the router go to get the next route. I...

Where does OSPF and EIGRP look when it has to reconfigure a downed network? Is it the Topology Table? If so, if I were to do a sh ip eigrp topology will that tell me what route the router will use to find a new route? Or is it the Neighbor table sh ip eigrp neighbor. I think I may be over...

Hey guys, I am still studying for my ccna. I just need to pass the icnd portion. Well I have small home lab that consists of 2x2501s and 1x1924 switch. I was thinking of adding another router to the mix. I can get my hands on a 1601 for around 55 used. Is a 1601 too old? I remember working...

techkiwi, Thanks for your post. I do not remember if the topology was using rip etc, but i was able to ping all devices, from all directions. I thought that if i can ping all devices that the routing table should be good. An I think that by the 3 minute mark to this sim I started to get mad...

Dan, Yeah I knew that going in but I thought I would try anyway. I was thinking about discussing this via e-mail but took a shot at this post. Like I said above it sucked that I got the same question both times and for the life of me I could not figure out what they wanted me to fix. On...

rcmp2k Thanks for the reply. We may have had the same sim. If you can remember were you not able to connect to the other router /network? Because in my case I was able too. My only problem was that I was not given the IP address of the far end router. I had to find it via cdp from the...

Hey Guys, Just wanted to throw my failure in also. I took the exam a month ago. I gave myself a gap of 1 month from when I failed the icnd the first time. What happened the 1st time was I was given a sim the 2nd question in and it was about a small network that consisted of 3 routers (both...

fizzak, Thanks, nice try but the problem is that everything is so small that even right clicking and going to display properties, appearance would be tough because you cannot see it. all the wording for anything is seriously about the size of the lines on the border of this box. Imagine...

Help guys, I am working on a dell pc 4700 (I think, pc is at home) with XP home and the problem is that the user complained that the icons on the desktop are very ver small. I go to look at it and I boot the machine w/o problems then when I get to the window login screen the list for user...

Thanks Guys, Arizona - Thanks for the info. I called Dell yesterday and the tech made it seem like I had to pay full price for the OS cd, because he said that I can buy one from dell or just go to any computer shop and buy the box version of xp home. I did not stay on the phone long enough to...

Hey guys, I have a Dell Dimension pc with a dead HD. It never makes it to windows and is making a clicking sound. My question is that the PC is out of warranty and I know I need to buy a new HD but they never sent out a restore CD to fix. My friend gave me a copy of XP home which was...