Search results for query: *

Needed to re IP the IPoffice once at install location, but not until I had already completed the ignition process on the bench off site. I went into providers, deleted old IP and added new IP of IPO. "put" the changes and rebooted server. Waited and hour and still get the FAILED connection to...

There are mixed select/non-select systems in solution" 1. What does "Set all nodes to select" do? 2. How to change a system back from select to regular server edition? Not sure how or why someone managed to set the 500v2 expansion and secondary server to "Select" mode, but they did and now...

IPO500V2 6.1(22) with 2 combo cards and embedded vmail. Direct dial "quit" working off the auto attendant. I have the direct dial allowed check box and the dialbynumber set on the digit 2. Attendant has been working since this was installed (6.1 so a couple years now). Programming appears...

I post too soon. What I show above works. It helps to save changes before testing them.....un-star for me

Server edition 9.4, 9608 sets, trunks are on 500v2 expansion. Default SYSTEM short code 9N/Dial/N/50 gives secondary dial tone just fine. I have user rights configured to point some users to an alternate ARS with different restrictions with a USER short code 9N/Dial/N/51. The 9N in the User...

Moving our secondary server (currently resides in same physical office and subnet as primary server) to a remote branch office. I am thinking I just need to change the eth0 on the secondary server to the new subnet and then remove/add secondary server. I am a little gun shy on it because of...

Robb thanks. The module referenced in that action tab is non existent. Likely an imported that didn't bring everything over. Do you have anything I cam reference to rebuild that piece?

This is an existing setup I am trying to work out 1 specific piece. Meet me works for creating and joining bridges using the 555xxxx format. When calling from outside to create or join a bridge there is an auto attendant where you can enter as participant or moderator. Moderator leg of the...

Thanks all, for furture reference: going from 8.1 to 9.0(sp2) by booting from ISO on a DVD and choosing upgrade during the wizard crashed the box like I have read in other posts. Not sure why I thought mine would go different, but figured it was worth a try. Get a good back up off the the...

thanks amriddle, very helpfull. Of course I am in the process of burning a disk now. And while I wait, why not ask?

Has to be DVD? Does USB work?

Seems like a simple question... but which file do I drop into the "Software Repositories" in the web interface to upgrade the linux box (going from 8.1 to 9sp2). I have the ISO file from the support site. I am thinking I "add" this into the operating system and applications entry then go to...

follow up as promised. IT "did their thing" on the switches and everything came up. No changes to my config

Thank you IPGuru for answering my question. I will post resolution after arm wrestling with IT

both are 105 at both ends, nice to make them match I have other networks I am referencing and I have an entry in the TIE field for one location. Have no idea why I would have changed that. It's been a long time since building that one

SC 21xx Dial 21N Line 105 (my ip trunk) extension are 21xx at the far end 24xx at the near end, relative to local short code ==== IP routes are good. ==== Do you expect an r5 and an r9 to talk and so I should keep plugging away at troubleshooting, or this will never work and I am chasing my tail?

Adding to an existing network of IP office systems, Hub and spoke config. New switch is 500v2 r9.o.2.o existing networked IPO's are all 406's 5.0(18) I don't want to mess with upgrading the entire network so I was looking to do a simple NON-SCN H323/H450 IP trunk and add short codes to dial...

FIXED!! I found the below article on sonicwall's support site. Based on this I tinkered with the NAT settings, and disabled/ignored the STUN results. Set my firewall/NAT type to "Symmetric NAT" and made a successful inbound and outbound call with audio. The article is an older document and...

From the IPOffice Monitor application under RTP sessions I see the call with: source ip 192.168.0.240 (IPO) port 49152 destination ip x.x.x.x (public IP of remote phone gateway) port 49652 So the IPO does see the call with both ports in the correct range. It really does seem like the Sonicwall...

Bass1234, stun is set on the IPO. stun results are in my first post. Nickgrill, Im kinda stuck. The sonicwall is dropping the UDP packets associated with the call traffic. Call setup, touch tones, etc all work fine it's just the audio. I can see it failing, but not sure what changes to make...