Search results for query: *

if i use an avaya vsu5, will it help to eliminate or reduce the delay on the clan card?

i have an ip403....can i forward my calls to an external no. so that when a certain no. xxxxxxxxxx dials my extension no. it will forward to the programmed external no. and when a certain no. yyyyyyyyyy dials my extension no. it shall not forward the call. in short can i filter the incoming...

i have an ip phone connected to a definity via linksys vpn router. my problem is i am having six to eight second delay before hearing the dial tone...pls help me with this one...

tks a lot morrack for your faster than sound reply...

i have an ip4610 phone to connect remotely to my ip403 via vsu5 on the remote side and sg200 on the ip403 side. is there any job aid that i can use to configure my ip phone and the vpn units? pls help..

my fax is connected to a pots extension (on my po 403) and i have to dial 9 everytime i use the fax.is there anyway to eliminete the 9...eg...line auto select in partner/magix...

morrack..my two ipo's will be in different area code...so i will ask my t1 vendor to split the t1(12 did and 12 data). mtvilla..are your ipo's in the same subnet? how does your incoming route look like? and associated shortcodes? tks for your help...

can i split my t1 so that i have 12 voice channels and 12 data channels that i will connect to a router then to ipo lan port? is that posiible?

is centralized vmpro possible using pri circuits that will connect my two ip403's?

thank u for ur reply ipguru...are u referring to the allocated answer interval under the telephony?

i want to change the no. of rings for calls to extensions before forwarding to the vm pro. i just could not find the way how to do it...anybody? right now it is 4 rings..

i have a new ipo403 with rel 1.3 and i tried to upgrade the unit but lost it and i tried to connect thru the dte port..i did the at and at-x commands but then the ipo responds with ok and i could not see anything more in the tftp log...maybe i dont have the correct mac address in the...

in my 403, incoming from analog trunks are directed to a huntgroup then to the member. but when the member is rna i want my aa greeting to answer instead of the huntgroup vm...pls help...

how can create a shortcode for direct vm transfer and assign it to a dss button so that i can use the same button to transfer to a user's mailbox by pressing the button and dialing the extension number? pls help...

how to create a shortcode for direct vm transfer and assgn it to my dss4450 so that i can transfer callers directly to a users mailbox? pls help...

i was able to connect thru spm by reducing down to 1200...i didn't have the chance of trying to dial out(using my laptop modem to internet) thru an analog extension but i will try to reduce the speed too... tks a lot for all your help...

i have a magix and i tried to use an analog extension line to connect my laptop pc's modem for internet access...i could hear the modem dialing the access no. then the sound of handshake protocol between modems but then the call will be dropped and the pc would try to redial repeating the...

hello kinghway...tks a lot for your help...i did as u said and now incoming calls are routed to *90 but i guess i need more help to program the attendant(i only have the start point) and how to record the aa greeting coz incoming callers are routed to *90 and hear nothing...tks in advance...

i want to setup an auto-attendant and main greeting recording on my ip403 release1.3.2 so that incoming outside calls will be ansewred by the vm/aa...any help pls...is it possible?

1. to jinxs - can i have the details on running the loopback test pls... 2. to fsoz - i never reboot, reset/busy/restore usually do the trick...my sync signal to all sites comes from the loop...