Search results for query: *

To whom it may concern, I would like help with practise exam for checkpoint r70 exam 156-215.70. I saw that boson is advertising practuse test in question but not sure how good it is, if anyone has used it please provide input thanks

Dear expert I willl be taking a course on check point r70 and would like to know if anyone took and pass exam if so have you been able to fine practise test as it seem not to be available online. Any help will do thanks

Hi Expert I install scruntiner and it is working great. I do see source and destination of high talker

ip subnet-zero ip cef ip domain-name ALTER.NET ip name-server primaryDNS ip name-server secondary DNS ip name-server Tertiary DNS voice service pots fax rate voice voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw ! *** Only for Managed...

Hi expert tftpdnld is not one of the options on this router when I did ? only dnld. I am now trying the xmodem. I could not get the 115200 to work and just settle for 9600 baud rate. It will be done in 4hr hopefully it works

Hi expert.I was giving a 3600 router but I can not seem to get the IOS loaded. I have perform the below steps how could I get IOS loaded. rommon 1 > set PS1=rommon ! > BOOT= ?=1 BSI=0 RET_2_RTS=00:34:30 UTC Mon Mar 1 1993 RET_2_RCALTS= rommon 2 > IP_ADDRESS=172.24.100.126 rommon 3 >...

Hi expert what I really want is redundancy. If moving gateway to 3560 would be the only option then I would be ok with looking at your recommendation. Do you have a quick design maybe

Hi expert if i will have vlan created on asa 5510 and that will be the gateway for the userlan t1 mpls=====rtr===asa5510===3560 user lan swt ==3560 t1 mpls=====rtr===asa5510===3560 swt not sure how to make this happen but your help is needed

Hi expert thanks for the config. basically the topology is setup so office does not go down.their are generator backup to building power and from the network side we will have two circuit from different ISP with two of each equipment on the core so their is hardward redundancy and circuit redundancy

Hi expert ISP do offer ppp multilink.I have only used it when multiple circuit is connecting to the same router. In my setup I need to have equipment redundancy on the core office can not go down, each router will have have one mpls t1 circuit. My routing protocol is ospf if possible a sample...

Dear expert I will be setting up an office and will like your help with a sample config for load balance of 2 T1 PIP mpls CKT between 2 router. each router will have 1 T1 for a total bandwidth 2megs for office traffic.

Hi Expert hub is 6megs mpls and spoke are T1 mpls circuit. When using concord physical interface does not show much traffic, but when checking tunnel interface on hub which has 512k bandwidth it some times show 100% utilization on receive or transmit load. tx/rx load 255/255. bandwidth on...

Dear expert I am confuse with physical actual size and VPN tunnel bandwidth.For example office has a T1 mpls ckt 1536. At this location we are using DMVPN tunnel with a bandwidth size of 512k. I had a report about slow performance, when I did a sho interface the physical interface reliable tx...

Hi expert I am task with setting up a network with dual communication failover only. I will not be able to have dual equipment failover please provide me a sample network design and config I would need to use all equipment I have to use only the equipment in file as this all we will be...

Thanks all I was able to get this resolve using all the steps provided. Once I decrease ip mtu on tunnel interface and remove tcp adjust-mss from lan interface. users came back.

Dear expert I am having a problem with mtu. spoke is setup with an ipsec gre tunnel using ospf. User are not able to access the internet or internal application. user are able to ping to the internet, ping to internal ip's. I all had configured ip nut 1300 under the tunnel interface and ip tcp...

Thats experts for your advise I will try and hope I do not have a major issue.

hi i would like to get help setting up a second vlan. I have a network which is in need of additional IP. I wanted to configure sample of how it could be done as below is what i nee to know.current setup for example 3 3560 switch with a default vlan call vlan 1.. Switch1 uplink to 2800 series...

hi i would like to get help setting up a second vlan. I have a network which is in need of additional IP. I wanted to configure sample of how it could be done as below is what i nee to know.current setup for example 3 3560 switch with a default vlan call vlan 1.. Switch1 uplink to 2800 series...

I will checked this and confirm if AV/ or microsoft update times. does scrutinizer keep track of data from previous days ? also I have nbar configured, and ip accounting am I on the right track