Search results for query: *

Hi All. I have been asked a question, and I can't find a definitve answer on Cisco.com, nor can I get hands on with an example of the hardware to test for myself. Does anyone know if ROMMON on an ASR 1002 allows the use of tftpdnld in the same way as other types of router? ALso is there a copy...

Hi All I have been trying to find a definitive answer on cisco.com, but have failed so far. Assuming I am on a router that has USB port, and an IOS that supports copy to and from USB, can anyone tell me the maximum size USB memory key I can use? I have seen various things that talk about...

Does anyone have a document that guides through upgrading IOS, Boot image and FDP files on a &304 with NSE-150? Specifically to load c7300-js-mz.122-33.SB9.bin c7304-fpd-pkg.122-33.SB9.pkg c7300-boot-mz.122-33.SB9.bin Cisco's release notes seem to point to a document for 7500, which is...

Hi all I have a number of sites where 837s are connected to BT ADSL lines. Some of them have an intermittent problem where the ADSL interface bounces. BT check the line, either from the DSLAM or on site and find it to be OK in terms of signal/noise when the router is disconnected. However when...

Hi all I have seen the dsl power-cutback command in a config for the first time. I looked on cisco.com, and it gives me a syntax for the command, but I am not sure what it does and how it is applied. If the config has: dsl power-cutback 1 applied to the ATM interface, and the default value...

Wastedyouth614 'wr' is short for 'write memory', which is exactly the same process as 'copy run start'. I prefer the copy command, because there is the possibility that you could accidentally type an extra character after wr. If you type 'wr e' that is short for 'write erase' which deletes...

Hi All Has anybody got a link to help me understand ADU and what its features and benefits are. I don't have any hardware to play with it on, and the BCMSN texts say next to nothing about it, but I keep seeing it in test questions.... Thanks EB

Hi Octavian I would expect 'conf t' to work too. Have a look at http://www.cisco.com/en/US/docs/wireless/access_point/1300/quick/guide/br13qsg.html#wp13691 EB

There is a command string to disable password recovery for security reasons: no service password recovery. I guess it is brought on by paranoia :-). This page refers to it: http://www.cisco.com/en/US/docs/ios/12_3/12_3y/12_3ya8/gtnsvpwd.html EB

A tip if you are using copy & paste-to-host in Hyperterminal. Set a line delay in the ASCII settings of Hyperterminal of 40 milliseconds. If you do that then you don't get any parts of the config dropping out because of the lack of flow control on the console port. EB

Look at 'monitor session' at http://www.cisco.com/en/US/docs/switches/lan/catalyst2970/software/release/12.1_19_ea1/command/reference/cli1.html#wp2788722 You will end up with something like Switch(config)# monitor session 1 source interface gigabitethernet8/47 both Switch(config)# monitor...

The first related page on cisco.com is this: http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008070f124.shtml Should get you started EB

Burt Apologies, I have found it now. Also possible on 1750-V. Thanks; have a star :-) EB

Hi Burt I have trawled Cisco's Feature Navigator to find an IOS that supports this. I can find no entries for 1700s at all. If you know of an IOS that will support trunks on a 1720, please let me know; it would make my life easier. Many thanks

Are you trying to treat one of your ethernets as a trunk? If so, the 1700 series cannot handle it. Trunking/multiple VLANs are not featured any any 1700 series IOS (as far as I am aware). It might be possible to do it using two sub-interfaces on the single ethernet port, and having separate IP...

I think you are trying to make your router accept a remote login via telnet from a laptop. You are currently connrected to the router console. So, set an enable or secret password as you have, then do: conf t line vty 0 4 password cisco login end The "Translating "int"... domain server...

One point. If the priorities are the same, then the router with the highest IP address on the VLAN becomes active. EB

I think you need to change the order, otherwise line 2 stops line 3 working. EB

Hi Has anyone out there got any experience of comparing 837 ADSL perfremance/stability with a router that uses a WIC-1ADSL card, such as a 1721? I have an issue where multiple 837s seem to lose the line as signal-to-noise ratio increases, but a 1721 on the same line seems to be stable. Is...

popasmuerf Go to http://www.cisco.com/en/US/products/hw/switches/ps628/products_tech_note09186a0080169696.shtml EB