Search results for query: *

Try Nessus security scan, or solar winds...there are others, but this is a start.

Also, on the asa platform, it is not the same. On the asa platform based on the model...the 5505 works like a switch, but the 5510 and above, you will need to configure subinterfaces on the asa and the asa assumes a trunk link to a switch off of the interface. In short the 5510 and above see...

You might be able to get away with this by doing a static for that specific server to the ISP2 interface. For instance as follows: ISP1 ISP2 | | | | | | ---------- ASA ---------- | | | Inside config could be as such nat (inside) 1 0 0...

Don't forget that you will need to ensure you define the pc's under the acl's for interesting traffic so that the vpn comes up.

Could be an odd issue with java, but what version of code are you using on the pix as well as what version of PDM are you using?

Perfectly stated.

Can you provide more information. What do you mean, "for some reason does not want to work correctly when setup for DHCP"? What happens?

Ebay. The 506e's are not expensive at all, you shouldn't have an issue at all.

tomrice, A few things here...It would definitely be helpful to look through some config guides, but some pointers on this one. 1) Per the config, the outside interface is in a shutdown state, you need to do an interface ethernet0 no shut 2) None of the acl's are applied, there are...

Not sure if you are still experiencing this issue, but seems like you are not advertising some of the routes. Are you using a routing protocol? Also, what is the topology like?

galloshes, this is correct only if you are certain that a certain traffic pattern should be hitting the device at that point in time if need be. In other words if there are no hit counts there are two reasons in which the acl is not being hit, one, there is not any traffic matching the ace entry...

I agree with many of the posts, two things are going on here..... 1) you definitely need to verify your T1 cross over, you should be using pins 1,2,4,5 and have them straight through on one end and flopped on the other end (cross over of course). 2)By default the clock source is line, set one...

Absolutely IOS version issue, which is why the command is not supported. Check your flash and see how much space you have, but you should be able to run 12.1 or 12.2 with no problems and have support for this. -Andrae

hello everyone, I recently passed the CCIE voice written exam and I'm studying toward the lab, does anyone have any ideas/plans for studies? I have been reading and going through the telephony and troubleshooting tutorials and performing installs, but not sure what exactly to focus on in terms...

Thanks, I figured it could come down to CER, we utilize that at one of our resorts as well. Thanks again, Andrae

I have a site here on a LAN with a CCM cluster. It is a campus environment therefore I have 4 different buildings on the campus with the primary building housing the CCM cluster, unity, voice gateways etc... I need to route 911 from the other buildings on the campus but still have it signal from...

I have followed your conversations and Kisco Kid is on top of things, great job guys. Just some insight on the Extreme. I love Cisco myself but I do work with Extreme and in fact own one for testing. The licensing isn't important so long as you have an accurate software code on your device. Just...

It hangs on an nwconfig screen at 0% and it says searching for and stopping installed products and underneath it shows some of the products it is looking for and trying to stop I guess but it shows bordermanager, console one, edir ....... The server does not run border manager either. I don't...

Hello all, I have just upgraded a netware 5.1 server to 6, no problem. I then loaded support pack 5 and had all kinds of issues due to files not being consistent etc... long story short, I re-ran the upgrade and all is well now in terms of the server and running just fine. When I attempt to load...

Hello all here's the deal. I have a cable modem from my provider, this one as with most give an ip address via dhcp. When I configured my router with the ip, subnet mask, and gw that my laptop obtained I was still unable to ping the outside world. The interface shows up and up but no luck on the...