Search results for query: *

Thanks Ben, I have the whole CA chain in the trusted ROOT in IE. Is there any other steps that need to be taken?

Self-signed cert ... I have it configged per the websites and Q articles that I have read. I have the server setup as the Enterprise Root CA.

Thanks sniper. I went through all three articles. I am still unable to connect ... when I perform start->run->outlook.exe /rpcdiag and enter the needed credentials I get disconnected. I don't have an ISA server or any other server in the domain. Also I have installed SSL CA's per petri's...

Reset the certificate services and re-installed. Not working still, any suggestions?

Thanks. I'll continue tightening the certificate services. Using the local certsrv ... should be fun. I left the firewall values at default. What should they be?

I have a single server that is handling everything. It is running Windows 2k3 server std and exchange 2003 std. It is also the DC and global catalog server. I have attempted to setup RPC over HTTPS only to be disconnected at every turn from the server when trying to use a HTTPS connection. I was...

Found a fix DSL filter. Excelsus Technologies model Z-200SM worked Z330TJA didn’t work both from Excelsus Technologies. Excelsus Technologies www.excelsus-tech.com 800-457-0967

CVRBOB, Can you resend that info with the typo errors? Not sure what "2 pairs Bl & OR pairs & a -48 VDC power unit on the green pair" is susposed to represent in cabling terms. Tom - not sure what you mean about using an ethernet cable. I'm not concerned about the connecting cable, just how...

Running a CSi R9.5 and sending SMDR over CLAN. My CMS vendor is telling me I need to enable RSP. What screen is this done through. IP-Services? Never turned on RSP before.

Can one of you smart cabling techs give me the exact pinout of the jack for the older hybrid phone connection. Also what pins carry power? 7&8 as is normal for Lucent? Does anyone have a diagram they have a link to - picture etc? Can you connect the BIS phones to a Hybrid port - TN762...

Can one of you smart cabling techs give me the exact pinout of the RJ45 - 8 conductor jack for the older Merlin BIS phones. Also what pins carry power? 7&8 as is normal for Lucent? Does anyone have a diagram they have a link to - picture etc? Thanks for the help!

Press Feature 59 and the software release will show. For the R6 - the latest was 6.04 and the 001 is the Country Code - USA.

The LEC is SBC and the CID info is stripped accurately on the other 4 CO Lines so that isn't the problem. I think we will try an ACS R6 at the DEMARC to see if we can repeat it there before our 25 pair 90' cable run to the telco room. Thanks all.

Have done those basic checks before - always wait 2 rings for CID info to show up. Have swapped line 1 & 2 and the CID issue follows the line. Basically have checked everything that is obvious and then some but the problem still persists. Again - CID info is passing through about 10% of the...

I have a strange one. We have 5 lines coming into a new building - about 100 ft of 25 pair cable to the telecom room and terminated on a 66 block. New ACS R7 processor - one the main line - CID data is showing up on the phones about 10% of the time. All other lines display CID data...

I need this PMSOIP patch #4814 installed on our G3si.9.5 switch ASAP as we just upgraded customer's PMS software to IP from a serial connection and it won't connect to the switch now. One of our Avaya techs has run into this problem before and this patch # 4814 fixed the conflict. Does any one...

We are working on a TN2404 on our test switch and at bootup all system tests pass except the "BTO TEST" which fails. Any Definity techs who are familiar with this failure who can pass along a tip or two as to what the BTO Test really is and what components on the processor would cuase this failure?

I don’t know if this will help I had to go to the full link and backtrack. ftp://ftp.avaya.com/incoming/Up1cku9/tsoweb/ The best thing is there Elmo web page witch has all there manuals http://support.avaya.com/cgi-bin/gx.cgi/AppLogic+Elmo you need to start with the list of documents...

That setup won’t work use this setup. The carrier gets a power signal from the 308EC and other modules wont work correctly if any other card is installed in the first slot the added CO ports have to be last because the don’t have ports assignment and would confuse the processor where the ports...

http://support.avaya.com/japple/css/japple?temp.groupID=107529&temp.selectedFamily=107548&temp.selectedProduct=107628&temp.selectedBucket=all&temp.feedbackState=askForFeedback&temp.documentID=129218&temp.selectedRelease=107849&PAGE=avaya.css.CSSLvl1Detail&aClass=japple.web.services.DataTransactio...