Search results for query: *

Hey, I am looking for firmware for my 5320 that still has the SIP web GUI, as my current version does not

Have you checked in the CallPilot web interface? The “Number of Rings” setting could be set to something other than zero

Hey all, I am trying to install Contact Center select 7.1 on Server 2012 r2, and it wants a feature/service pack. I do not have the service pack, and cannot download it from Avaya. Can someone send it to me?

Hey all, I have an SV8100 system with the UM8000 card, but the CF card is gone. Does anyone have a disk image of the card that I can restore onto a generic CF?

I am unable to disable the DSP in question, It says the parent card is not in service, and when I try and enable the card, it tells me to run out of service diag, and when I do that, it says "some dsps faulty on vp card"

My Option 11 has Meridian Mail, and I can access it from TTY 0. Only issue is; I cannot dial meridian mail, I have ACD agents setup, the access DN is correct and all, but MerMail shows DSP Port 7/8 to be faulty. How should I go about this?

What field in MerMail will allow me to see the messaging dn

I have access to meridian mail. Is there a guide to how i need finding the VM DNs?

I want it (for now) to be an external VM access number. You call the number, and it answers “Meridian Mail, Mailbox?”

I did. Sadly no effect. I think the set is broken. Now one more thing. I have a universal trunk card, and a CO trunk on TN 5 0. How would i route that directly to meridian mail

I get nothing. it says NPR503 and nothing else

.idc 4 => NT8D02GA 06 NNTM60G3JAEW 0000

SCH0000 TN 4 0 DATE PAGE DES DES MRDIAN TN 004 0 00 00 TYPE 2616 CDEN 8D CUST 0 AOM 0 FDN TGAR 0 LDN NO NCOS 0 SGRP 0 RNPG 0 SCI 0 SSU XLST CLS CTD FBD WTA LPR MTD FND HTD ADD HFD MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1 POD DSX VMD CMSD SLKD CCSD TENA SWD LND...

NPR503 .stat 4 00 = UNIT 00 = IDLE (2616) 01 = UNIT 01 = UNEQ 02 = UNIT 02 = UNEQ 03 = UNIT 03 = UNEQ 04 = UNIT 04 = UNEQ 05 = UNIT 05 = UNEQ 06 = UNIT 06 = UNEQ 07 = UNIT 07 = UNEQ 08 = UNIT 08 = UNEQ 09 = UNIT 09 = UNEQ 10 = UNIT 10 = UNEQ 11 = UNIT 11 = UNEQ 12 = UNIT 12 = UNEQ 13 = UNIT 13...

All looks to be OK. Card config is fine, but the set still shows idle

I honestly believe my set is crap. I measured line voltage and it was all good, I also connected a Norstar set (to see if the BLF lights flashed) and it flashed the line keys. So my set has crapped itself, and now I need a new one.

How do I find the TN? I moved the card to slot 3

I have been trying for over one hours now to get one singular M2616 to work on a digital line card. I have enabled and gave it a TN, but it refuses to power up. Is there a specific loop that I need to use for slot 1?

Do you know the pinout on how I can make this myself?