Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
-
WS-X6748-GE-TX question
I realize this is a hard question to answer... of course I realize the bottleneck is the 1GB server connection...BUT, because it's on a 6748-ge-tx, it does have 40GB to the backplane to work with as far as buffering / queueing packets out of the port...none of the floors where the end users... -
WS-X6748-GE-TX question
Trying to calculate how many end-users would be able to pull down data at 100Mbs each from a Server that has a 1Gb connection to a WS-X6748-GE-TX card, presuming worst-case scenario in which every user would be maxing out their respective 100MB connection, bearing in mind that the server’s 1GB... -
CCNP- BSCI (642-801) * BGP synchronization QUESTION
A ROUTER-D ------- ROUTER-E >>>>> ROUTER-F (AS 64500) S | eBGP 6 | 5 ROUTER-C ------- ROUTER-B >>>>> ROUTER-A (AS 65000) 5 eBGP 0 0 I'm the Fanciest of the Fancy...INDEED- FANCYpete
- Post #2
- Forum: Technical certification and testing
-
CCNP- BSCI (642-801) * BGP synchronization QUESTION
Hello all, I am getting conflicting information from a testing engine that I'm studying with. The question is as follows: No IGP is running in AS 65500 (routers B,C,D,E). Router B peers with Router A (AS 65000) via eBGP. Router A advertises (172.16.0.0) Router E peers with Router F(AS 64500)...- FANCYpete
- Thread
- Replies: 4
- Forum: Technical certification and testing
-
Bandwidth
Priority queuing, like all methods of queuing can only be enabled on interfaces with bandwidths less than 2.048 Mbps. In other words, you aint gonna configure queuing on an ethernet interface. So it's for a WAN link, like ISDN or frame relay. Now listen up people! If your link is already... -
Crunch Time (One week to go)
Don't rely on Testking. You want to gain a very solid base knowledge of all the concepts covered in the CCNA 640-801 exam. I just passed with a 958, and all I used with the Cisco Press CCNA Flash Card book with the Exam Practice pack that is included. I found that taking the practice tests...- FANCYpete
- Post #6
- Forum: Technical certification and testing
-
Average CCNA scores??
Not that it matters, as long as you pass (849 and up)..but I was just wondering what some of you out there got for scores on the CCNA exam. Trying to gauge what the averages are for people that pass. I'll start...958 I'm the Fanciest of the Fancy...INDEED- FANCYpete
- Thread
- Replies: 5
- Forum: Technical certification and testing
-
1760 - No T1 WAN Connection
Matt, are you all set? I'm the Fanciest of the Fancy...INDEED -
1760 - No T1 WAN Connection
Matt,glad to see you've taken the bogus ACL's out:) Also, glad to see the default route has been added. Your current config is good to go , except that you need to define your clocking, framing, coding, etc on SERIAL0/0. To do this configure the following for interface Serial0/0: interface... -
DNS not working with ACL
good point Chris, I concur. I was assuming he was running his own DNS server. I'm the Fanciest of the Fancy...INDEED -
1760 - No T1 WAN Connection
Matt don't worry, the default encapsulation on a serial interface is HDLC. You're not running any dynamic routing protocols, and you do NOT have a default route, you may want to add the following to your config: ip route 0.0.0.0 0.0.0.0 65.86.196.225 Also, never paste in a config with your... -
Setting up NTP on a Cisco router
Sounds like a plan guys, Bob you may also want to add the following to your ntp setup: ntp clock-period 17179938 <--- (Amount to add to the system clock for each clock hardware tick (in units of 2-32 seconds). ntp source Loopback0 <--- (provided you have a Loopback address) ntp... -
Can't ping routers in my home network.
by the way, to run the c3620-is-mz.122-7c.bin, your routers are going to require at least 48Mb RAM, and 16Mb of Flash happy upgrading! -Pete I'm the Fanciest of the Fancy...INDEED -
Can't ping routers in my home network.
yes, you have to enable trunking between all of the VLANS and your home network(Dlink). IP PLUS is just a feature set that will allow you to configure the ISL trunking. FYI: ISL- Inter-Switch Link= Cisco-proprietary protocol that maintains VLAN information as traffic flows between switches... -
Cisco 2500 - reboot needed twice a day
What kind of connection do you have to your ISP, is it Frame-Relay, if so what is your bandwidth limitations? What's the CIR, and port speed? If you are saturating your pipe regularly, i.e. maxing out both INcoming ,and OUTgoing bandwidth and it requires a reboot of the router to get you back... -
DNS not working with ACL
yes, indeed this is the reason, you will need to permit it OUTbound as well as INbound on your interface..hope this helps I'm the Fanciest of the Fancy...INDEED -
Newbie question
Hi manishgp, spudnuts is 50% correct, 254 is the administrative distance on your route that you have pasted in your original entry : "ip route <nn.nn.nn.nn> <255.255.255.0> Null0 254" HOWEVER, It could not be a tag for controlling redistribution via route maps without the required... -
827 ADSL Router WAN Interface Configuration
Hi illegalop, call it a hunch , but it sounds like you have a default gateway problem here. So, from the inside, you can ping the ip address of Dialer1 (x.x.x.x /29), but can not get past it? If this is the case, try changing your default route from "ip route 0.0.0.0 0.0.0.0 Dialer1"... -
DNS not working with ACL
It depends where you have the ACL applied...is it on the IN or OUT of your Serial connection ? Does it look something like this? access-list 101 permit tcp any any eq 53 access-list 101 permit udp any any eq 53 I'm the Fanciest of the Fancy...INDEED -
Certification advice?
No sir, no Grace period. You'll have to take the CCNA exam again. I'm the Fanciest of the Fancy...INDEED
