Ok, I finally got it to work. Perseverance paid off. :)
Here is the final config for documentation purposes of others that struggled like me. No, I do not know what the final steps that made it work, part of it was reconfiguring my firewall (Watchguard XTM 22).
hostname "LAR1-CORE"...
ok, got the new switch, fresh clean config. Loaded up the following:
ip routing
vlan 1
name "DEFAULT_VLAN"
untagged 49-52
ip address dhcp-bootp
no untagged 1-48
exit
vlan 36
name "Voice"
untagged 1-48
qos priority 7
ip address 192.168.7.2 255.255.255.0
tagged 50...
I've got a brand new HP Procurve 2620 POE switch showing up today. Once I get that in, we will know a few new things. 1) Does this LLDP-MED stuff only work with a POE switch 2) will a new switch (NON POE) work? I have a 2 new 2910al's in for a different project. Since it would have the...
So, the firmware for each of my test switches are at the latest that HP provides. There are two switches I have been playing with:
2824 (j4903a) - i.10.77 released 08/26/09
https://h10145.www1.hp.com/downloads/SoftwareReleases.aspx?ProductNumber=J4903A
2810 (j9021a) - n.11.52 released...
Thanks Vince, thanks Cajun. Yea, that document I came across a while back.
I think my problem is partly stemming from the cisco phone will not pick up the DHCP address associated withthe voice network. LLDP-MED is enabled on the phone, and I have obviously designated the "voice" parameter on...
So I added the switch into the mix this morning. I'm using a 24 port (Procurve 2810) and am only using a small subset of the switch for testing. Ports 13 through 20 specifically. For now, lets just ignore everything else.
vlan 1
name "data"
no ip address
tagged 13-20
qos priority...
Ok, just another update before I head to the house for the day.
I went back into the firewall (Router), changed what I want to be the "Voice" VLAN to UNtagged, and the data to tagged. Now when the phone boots, it grabs a Voice VLAN IP address, 192.168.7.101 (instead of the data one).
I...
Ok, router (Watchguard Firewall) supports vlans, I'm just diving into new territory here, so this will take me a bit of time to figure out. I got two vlans defined on the port (just like the switch config above). I re-defined my VPN tunnel on both sides, Corporate and remote site (It's good to...
From re-reading through what I wrote, and reading a few other docs, I cannot have two ports untagged at the same time. So, with that in mind, the config would look like this:
ip default-gateway 192.168.6.1
ip routing
ip route 0.0.0.0 0.0.0.0 192.168.6.1 (or would this be 192.168.7.254?)
vlan 1...
Thanks for the post back VinceWhirlwind.
So, if I am adding back in 49-52 as tagged on each vlan so it can propagate out, then I would change the Voice VLAN to untagged (like in the example below), or would I just have tagged 1-52 instead?
ip default-gateway 192.168.6.254
ip routing
ip route...
Hey folks,
New to this board. I did do a bit of searching, read through this article (http://www.tek-tips.com/viewthread.cfm?qid=1656061 which VinceWhirlewind had some good insight). I am new to the HP world (Mostly light Ciscoing) so my questions may sound incorrect. Also, I inherited this...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.