Search results for query: *

Hi Hahjoel You can do a no nat-control on the firewall,they only thing you will need are just access-list permit the different subnets

Hi your question is not clear what you require help with, you have two devices Cisco & DD-WRT, what are they connected to? another thing the WAN that your referring what device is connected to? how are the three devices Cisco, DD-WRT and Netgear connected?

Then your QoS is wrong hence why its not working the way it should be working. In QoS the ACL only identifies the traffic we want to mark, so what your doing is just identifying the traffic but not doing anything with it. You need an ACL to identify the traffic your interested in. then the DSCP...

can you please print the input policy and dscp making

Good day please note that i shutdown my cisco 6509E catalyst switch, and it came back in to a rommom> mode. error "*** System received a Software forced crash *** signal= 0x17, code= 0x24, context= 0x423586b4 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002". i tried rommon 1 > dir...

Hi all Im new to backup and i hope the forum will help me with my problem. im using veritas netbackup 6.5.6 to backup folders on a 64bit windows 2008. The backup goes through fine but the folders i empty. when i check the folders, they have data. please help. your response will be highly...

Thanks for response Vieron82 the serial interface on the service provider's side was administratively shutdown

hi all im having a problem with a serial interface on a cisco 1900 router. the status is up down. the line protocol is down but the service provider says they can see the CSU/DSU. when the service provider loops the line the line protocol goes up but when they removed the loop it goes down...

Chieftan its connected to an HP docking station. VinceWhirlwind GigabitEthernet0/42 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 18ef.6396.2b2c (bia 18ef.6396.2b2c) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255...

hi all i have a port that keeps going into err-disabled mode and shutdown. i configured err-disabled recovery on the switch but the port still doesn't get back up. below is a log results and err-disabled configuration Aug 29 07:09:20.628: %PM-4-ERR_DISABLE: link-flap error detected on Gi0/42...

hi all i have a port that keeps going into err-disabled mode and shutdown. i configured err-disabled recovery on the switch but the port still doesn't get back up. below is a log results and err-disabled configuration Aug 29 07:09:20.628: %PM-4-ERR_DISABLE: link-flap error detected on Gi0/42...

hi guys just for interest sake, this it what i did. i added the new range as a secondary IP address on the router and routed the ips to the firewall. on the firewall i have them natted to the inside.

the make is cisco ASA 5510 and i have never heard of option 1, how does it work. and option 2 does the nat work the same way and do i have to change the name of the interface from outside to something else or the physical interface stays as outside without an IP address and the names are applied...

my ISP has given me a second range of public IPs on the different subnet as the first range. the first range 196.40.172.84/29 and now they have given me 196.40.162.48/28. the router interface 196.40.172.85/29 is connected to the firewall interface 196.40.172.86/29. if i add the new range...

Hi all can someone explain to me the concept of secondary ip address on router interface. are the two ip address active after setting the secondary ip address or the secondary is just stanby?

hi Vince thanks very much for your help. i really appreciate it, everything working fine. my skype name is tefo3456 i could do with network engineer friends

the command is ip routing.

i wanna know if its safe to patch them directly into the firewall, like at the moment they are connecting directly to the internal network and we wanna put a firewall in between

hi Vince the routers interface are on a different subnet. for example 196.40.172.1/30, 10.50.100.1/30, 10.59.8.1/30 and they are all looking for the .2 address as the next hop. please bear in mind that this routers are operationsl and are the third-party so changing the interface ip is out of...

you might wanna put in a static nat like nat(inside,outside) static tcp 95.*.*.218 110 192.168.1.10 110