Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. CommoGuy101

    Trunk to Trunk transfer

    All has been resolved. Ended up being an issue with PNI. They were a mismatch. The ISDN (local PRI) was set to 00000 for the PNI The TIE to Cisco was set to 00001 Changed them to 00000 so they would match and "BOOM" all is working properly. Thank you all, CommoGuy101
  2. CommoGuy101

    Morning everyone, I have an issue

    I have it resolved finally. Turned out that the PNI for the local PRI was set at 00000 and the PNI on the TIE trunk was set to 00001 Changed the TIE to be 00000 and all is working properly. Thank you all for your input and help. CommoGuy101
  3. CommoGuy101

    Morning everyone, I have an issue

    The TARG on the TIE route is open completely. No TARG entered When doing a trace on the d-Channel, which D-channel...the one for the local PRI or the TIE trunk should I look at ? The weird thing is I can send it over a TIE to a remote Nortel system and then route it to CISCO using a TIE on...
  4. CommoGuy101

    Trunk to Trunk transfer

    FRL is set to 0 on the routes Changed the settings for the NCOS Still getting the same results. Extensions on Nortel can call extensions on the CISCO using the CDP routing. Only fails when a call comes in on the local PRI then trying to route via CDP to the CISCO. CommoGuy101
  5. CommoGuy101

    Morning everyone, I have an issue

    Both of those are set to"YES" When calls come in on the Local PRI, I can CDP a call from Nortel CS1000 to another Nortel, proving that trunk to trunk transfer is working. But when I CDP to the QSIG connected to the CISCO the call is diverting to the attendant console.(as if it doesn't even see...
  6. CommoGuy101

    Trunk to Trunk transfer

    I checked the CDB and those were already set to yes DITI YES TRNX YES EXTT YES FTOP FRES When I check the ESN I have noticed that all were set to 0 When I look at my other sites those are set 0-,1-1,2-2 and so forth NCOS 0 - 0 NCOS 1 - 0 NCOS 2 - 0 NCOS 3 - 0 NCOS 4 - 0 NCOS 5 - 0 NCOS 6 - 0...
  7. CommoGuy101

    Morning everyone, I have an issue

    I have tried changing the DDTI to "yes" I get the same results Calls are diverting to the main console. I should also say that there is a TIE trunk between to Nortel CS1000 and Nortel Option 11. The calls work properly when CDP to the to the Option 11. All looks like the same set up to me. I...
  8. CommoGuy101

    Trunk to Trunk transfer

    Morning everyone, I have an issue with trunk to trunk transfer...I believe I have a local PRI on my Nortel CS1000E with a block of 100 DID numbers Recently, I have set up a TIE trunk between the Nortel and Cisco. I have taken a DID number and then did a CDP of that number to the Cisco system...
  9. CommoGuy101

    Morning everyone, I have an issue

    Morning everyone, I have an issue with trunk to trunk transfer...I believe I have a local PRI on my Nortel CS1000E with a block of 100 DID numbers Recently, I have set up a TIE trunk between the Nortel and Cisco. I have taken a DID number and then did a CDP of that number to the Cisco system...
  10. CommoGuy101

    TMDI Issues

    Thank you all for your assistance. I moved everything over to the carrier with clocking and all is fully operational.
  11. CommoGuy101

    TMDI Issues

    After I did n INI, I was able to successfully FDL the TMDI card. I can enable the loop and Dchannel and perform a loop back Now I am at the point where I think I need to do the clocking. I have placed this TMDI in a carrier that no other PRI is installed or a clocking source I don't have a CC...
  12. CommoGuy101

    TMDI Issues

    Sorry That is 4 1 4 for the TMDI
  13. CommoGuy101

    TMDI Issues

    Release 7 is what I see I have done in this order RST TMDI 4 1 1 SLFT TMDI 4 1 1 (test pass) ENL TMDI 4 1 1 FDL Hate doing an INI and not sure that will even solve it.
  14. CommoGuy101

    TMDI Issues

    REQ iss VERSION 4021 System type is - Communication Server 1000E/CP PM CP PM - Pentium M 1.4 GHz IPMGs Registered: 3 IPMGs Unregistered: 0 IPMGs Configured/unregistered: 0 RELEASE 7 ISSUE 00 Q + IDLE_SET_DISPLAY Lodi Community Hospital IPMG TYPE CSP/SW MSP APP...
  15. CommoGuy101

    TMDI Issues

    After the RST command, I have done the slft tmdi 4 1 4 and all passes SELFTESTS PASSED CARDID= NTRB21AA How can I determine what type of cabinet, chassis?
  16. CommoGuy101

    TMDI Issues

    When I do the RST TMDI 4 1 4 I do get the OK However if after that I try to ENL TMDI 4 1 4 FDL it just sits there. After it sits there for so long, I am able to **** out of the load but nothing has taken. I have let it timeout as well. Still don't get a n active TMDI .stat tmdi TMDI 000 0...
  17. CommoGuy101

    TMDI Issues

    I originally built this on 0 1 5 and was getting the same issues. So I moved it to an open slot 4 1 4, after outing everything and then re-adding it all. I still get the same results. Are there specific slots I am to use for TMDI?
  18. CommoGuy101

    TMDI Issues

    Hello All, I am having some issues enabling a TMDI card. I have built the DLOP in the CEQU Built the DCH Created the Route Add the TIE members Clocking is set up stat TMDI and I see: .stat tmdi TMDI 000 0 1 ENBL TMDI 000 0 2 ENBL TMDI 004 1 4 MAN DSBL I have tried to enl TMDI 4 1 1...
  19. CommoGuy101

    Default gateway

    Hi All, I am having some issues today pinging my default gateway on the Nortel CS1000 I have a route built and active: 0.0.0.0 to 137.135.128.1 I am unable to ping this IP address. All of this was working properly. We had a hub go out and moved the connections to a switch. I am not sure if there...
  20. CommoGuy101

    Bug 9024

    I have not looked at the history file. What am I looking for in the file? CommoGuy101

Part and Inventory Search

Back
Top