Search results for query: *

I redid the RLI to show the long distance on top and them the DSN. I created a DMI for 28 that subtracts 1 digit. 8 & 9 are already set to LOC in the ESN under AC1. I still get the message when I try to dial the long distance number using 98 or 99. the DSN still works with no problem.

We have a CS1000-E 5.0 DSN switch that uses pre-emption dialing. the problem that we are running into is our state has one area code, and a majority of the nxx's are long distance. I am trying to create a RLI to route this properly. I have created a RLI with a Entry 0 with our DSN trunk and...

We have a VTC system that uses a PRI for acces to the outside world. Recently it has not been working and we keep getting a ISDN error "Incoming call barred" when using it and a PRI222 DCH: 35 DATA: 00000006 PRI229 DCH: 35 DATA: 00000000 when trying to call it. [highlight...

This is our DLOP DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD PRI 35 23 esf no b8s fdl - 00 004 0 08 The dch is 35. still getting the same problems.

I am getting this error when trying to dial the trunk. [highlight #FCE94F]PRI222 DCH: 35 DATA: 00000006 PRI229 DCH: 35 DATA: 00000000[/highlight] Below is the configuration of the PRI. [highlight #FCE94F]TYPE RDB[/highlight] CUST 00 ROUT 35 DES VTC TKTP TIE M911P NO ESN NO RPA NO...

the 790 is the direct access to the outgoing trunk (ACOD)

The trunks are setup with a NCOS that allows calls to all the outgoing trunks. The settings in NET_DATA is setup for trunk to trunk

We have a internal ISDN pri TIE trunk used for our VTC system that is not able to dial out on any of the outgoing trunks (Local, DSN,Long Distance). We turn on D-channel messaging on this trunk and come up with this when it is trying to dial out. DCH 35 IMSG SETUP REF 0000800A CH 0...

We are getting some errors and wondering if anyone had any ideas on these. One is: AUD093 000019AF 0000181C 0F0A9327 00000001 00000000 000019AF 0000181C 0F0A3327 0 0000001 00000000 Second one is: 8UG5112 8UG5112 : 00001E04 00001E73 14 8UG5112 + 008F07FC 0088CCC8 0088C65A 0088C059 0088AE63...

0 is just showing the NXX number where 1 shows the full number

I found it, there are two entries. one of the entries has ESA_HLCL to the number I am looking at doing. I am assuming that I assign this to the outgoing T1's.

Trying to find out what load that is in

The people who maintained this have moved on. I somewhat familiar with most stuff on the merdian. Just not sure where to look for this on our outgoing trunks

One is for local calls, one is for long distance, and one is for what is called DSN calls

I have three different trunks leaving the switch all are ISDN T1's. I want the the caller ID to show the correct DN if calls are done within the switch. I just want it changed for any calls accessing these three trunks.

I am looking to keep the extensions for calls that are within the switch. When we access the outgoing trunk lines, I would like all numbers using that trunk to read one number

How do you verify in programming what digits are being sent out for caller ID. We are trying to get our block of number to show one number when calling outside of our switch.

The dongle is in there and has a green light on it.

I am getting this message when logging into the web page. Login failed because the TM server is missing the required security device (Dongle) Have tried a restart and that did not help. Not sure where to check for this, to see if it does see the dongle.

I go here https://app91.nortelnetworks.com/espl/index.cfm I do not see where the peps are for the callpilot system.