Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: dogg1
  • Order by date
  1. dogg1

    HP Array Battery replacement

    Hi All, Has anybody come across thier array battery disabling for their Signaling Server's? We have HP DL380's G7 and I'm trying to see if there is a way to get the status of the batteries via the linux cli. I have tried a few commands but no luck. Thanks in advance Jeremy
  2. dogg1

    Cisco Analog Gatway FXS Port to Valcom Paging

    Hi All, We are migrating off our PBX and over to CUCM. In doing so, I'm trying to test our Valcom overhead paging system using an FXS port. The FXS port is connected up to a Valcom 9940(station Level page adapter) converting the fxs dial tone to 600ohm connection to the 9 zone paging...
  3. dogg1

    CUCM SNMP Set Command

    Hi All, I'm trying to test an snmp alarms on our new CUCM Cluster. I have everything setup correctly in CUCM and I try to use the snmp set command in CLI. It is complaining about the dash in snmpset -c <community string> -v2c. Any suggestions or idea why this is not working? Thanks Jeremy
  4. dogg1

    SRPT316 Internal communications message transmission failed.

    Oops, I forgot to add the actual error message. Here it is: SRPT316 Internal communications message transmission failed. % (Transport: AFS; Subject: accountDB_BannerUpdate; Action: PUBLISHER; IP: 192.16 % 8.202.57; Reason: 11; Details: ) Thanks JW
  5. dogg1

    SRPT316 Internal communications message transmission failed.

    Hi All, I started getting this message last Monday, it happened once and then again today. It only happens during midnight routines. The error is coming from an MGXP. I can see that its registered. I telneted to the MGXP and did a joinsecdomain anyway and ran mids again and recieved the...
  6. dogg1

    Newbie question

    Hi All, We are currently migrating off our Avaya System and onto Cisco UC System. I have never worked with SNMP. I'm getting ready to alarm a couple Clusters. We will be using V3 SNMP and sending SNMP/Traps to Solarwinds. I have double checked all my config more than once and I still cant...
  7. dogg1

    Getting Fir0016 and fir0017 about the same time the last two nights.

    Hi All, I have received fir0016 and 0017 at 7:15pm the last couple of nights. Performed tests on both the controller and network card, both passed. Any suggestions as to what might be causing this error messages? Its very odd that they occur the same time each night thus far. Thanks in Advance!
  8. dogg1

    Blower fan replacement

    Hello All, Do I need to disable the System Monitor card(TTY Port) and pull it out to replace a blower motor? Thanks in advance.
  9. dogg1

    Can a virtual loop be segmented?

    Thank you both for the replies. I have found my answer. :)
  10. dogg1

    Can a virtual loop be segmented?

    We have a cs1000 7.6 system. Recently we have moved a lot of workers to 2050's. In doing so they were built on virtual loop 224 1. Can you segment out a virtual super loop?
  11. dogg1

    Fiji007 and fiji010 0 0 0 errors

    Hi All, Last couple of nights I have recieved these errors. FIJI010 0 0 ALARM 00 - RECVS_FROM 00000001 % % FIJI007 % NEW STATE RING 0: NONE % RING 1: FULL % % FIJI010 0 0 ALARM 00 - RECVS_FROM 00000003 % % FIJI007 % NEW STATE RING 0: HALF % RING 1: HALF I...
  12. dogg1

    AML 0 Maintenance notification

    Hi All, I have a question: We recently had one of our PBX's INI. Now I get this maintenance message, DA AML :: Info :: AML: 0 MAINT INDICATION TIME, that comes up. I checked AML 0 and it use to be used for the old vm system. See below for the print out. ld 48 LNK000 .stat aml 0 AML: 00...
  13. dogg1

    Can you do a trace route from an MGC Card?

    All, I was looking in the MGC Card and couldn't find any obvious commands under the "help" menu. Can a trace route be performed on an MGC Card? Jeremy
  14. dogg1

    Installing a Second Signaling Server.

    Thank you for the information. I have one last question. To this point I have always build a primary and backup security servers with SS and EM. I plan on going with a member server, do I still deploy the EM portion of the applications? Thank you for your help. Jeremy
  15. dogg1

    Installing a Second Signaling Server.

    Hi KCFLHRC, We have SIP trunks to the site. My understanding is if the primary fails the backup should take over correct? I hear you about rebuilding the Primary. It's a pain I do have another question for you. When you build the backup under the security section it asks for the IP of the...
  16. dogg1

    Installing a Second Signaling Server.

    Hi All, We have a CS1000E site that has a Primary Security Server. We will be adding a Virtual DCH and sip trunks to this site. To give us redundancy we want to add a backup security server in case the primary goes down. Its been a while since I initially install this sig server. Are the...
  17. dogg1

    M2000 SERIES NT2K40WA EXTERNAL ALERTER question

    Hi All, First of all has anybody used the NT2K40WA? If so, is there a power board that gets installed on the 2616D as well? If so, does anybody know the part number for the power board? We use to have a 2616D with a on-board NT2K40WA. Somewhere along the line the phone was removed and is...
  18. dogg1

    Dialing Callpilot Mailbox and encrypting password question.

    All, Is there a setting on the PBX or CallPilot to mask/encrypt the password on your CLID of your phone when accessing your voice mailbox? Thanks Jeremy
  19. dogg1

    CS1000E Wall Cabinet to CS1000E 1010 chassi.

    I should have added that the CS1000E has MGC Cards and a CPPM for a processor. Also, we do have a CPDC Card for SS, but site doesn't have Voip sets.
  20. dogg1

    CS1000E Wall Cabinet to CS1000E 1010 chassi.

    All, We are moving a site from a location that has a cs1000E using the wall cabinet(old opt. 11c cabinets). I was curious if I could use the 1010 chassi's at the new site and just migrate the existing cards from the opt. 11C cabinets. If I can, is there programming changes that need to...

Part and Inventory Search

Back
Top