Search results for query: *

Mr.TeleLion, Im sorry,our system is TSWSP4. <CADAP; CALENDAR DATA IDENTITY=SABIC-HQ VERSION=CXP1010104/4/TSWSP04/R5A 16:18:49 THU 03 SEP 2009 END </****** END OF PRINT ******/ Can u give the configuration of MD side(ROCAI,RODAI,RODDI,RODDI,RINII,RINIP)if possible can u give me also...

corrections: RODDP:DEST=71,IPOPT=YES; DEST=71,ROU=70.IP ADDRESS=11.2.200.240

Mr.TeleLion, Can u check if my configuration is right. RODDP:DEST=ALL; EXTERNAL DESTINATION ROUTE DATA DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE 71 70 160610000000125000600000000 0 3 0 <RODDP:DEST=ALL,IPOPT=YES; EXTERNAL DESTINATION ROUTE DATA...

Im sorry,our system is using TSWSPO4 not MX-ONE. <CADAP; CALENDAR DATA IDENTITY=SABIC-HQ VERSION=CXP1010104/4/TSWSP04/R5A 16:18:49 THU 03 SEP 2009 END </****** END OF PRINT **** Mr.Telelion,can u give me the step by step configuration i n MD Side (ROCAI,RODAI,RODDI,RIANP,RINIP) and if...

The issue is I forgot to program the ip address in RODDI. When I make RODDI:DEST=20,IPOPT =YES, I did not see the IP. Thanks Again

Hi Again, As usual I have problem again.We are configuring IP Trunk between Saudi and USA.In Saudi we are using MX-ONE SP4 and in US they are using AVAYA.Can somebody give me the step by step configuration in AVAYA and in MX-ONE. Thanks in Advance

Thank you very,very BIG.My problem is solved.thank you for your response,guys.Your d BEST.Thanks again.

hi everybody, please help me in my problem.we have a IP (Networking)Trunk here in jeddah and dammam,saudi arabia.we are using Ericsson Consono.Both Consono connected via IPLU CARD.If the caller from dammam call to jeddah,the call goes through but jeddah branch call in dammam,i see the telephone...

hello everybody, please,can somebody help me how to change the IP address of NIU and IPLU.

its ok now,problem solved.I replace the NIU2 board.thanks for your help.

Just send your inquiry in tektips,if i know i wiil help you.there is lot of expert in tektips forum

I want to access one of our sites in my house via modem.I call the technician to remove and re insert again the NIU,after re-insert the NIU,I can acess the MD but after 5 minutes when I will access again.I cannot access.

IOPWP; (To print the password) IOPWC:AUTH=7,PSW=_______; (To change the password (BC9). To remove the system password associated with authority class 1. IOPWC:AUTH=1; For BC13 AND UP: To change password of auth.7. Signin in highest category (cat.7) 1.IOUAP...

i restart the board,pull-out and pull-in,still I cannot access in remote.I want to replace the board.what is the command to replace the existing NIU?

I have problem to access NIU2 in remote,I think there is problem on NIU2. How to change the NIU2 Board?

kank, thank you very much for your quick response and for your help.youre the best.good luck.

we have 3 md 110 system in our company (BC 13),We are planning to add 1 lim.can somebody give me the step by step command how to add new LIM.

The problem solved,I swapped the DSU in mag.0 to mag.1 and DSU in mag.1 to mag.0.

Try to restart all the TMU boards,

Is this happen on all analog extensions or only one extension,if this problem happens only on one extension,try to change the tel.set or restart the program unit for analog,RFPUI:LIM=location of analog extension,UNIT ELP6,restart the board RFBOI:LIM=X,BPOS=X-XX-XX;and then...