Search results for query: *

Queball, That worked. Now to just figure out why VM isn't picking up.

Thanks QueBall, I think that did it but since I'm working remotely and don't have VM or anything else set up to be sure, I won't know until the morning. I can say without a doubt I didn't get a fast busy. :)

Good evening all, I have been a long time lurker and have gotten some great tips, but this is the first time I have posted for help. I just purchased a USED BCM 50 with all the necessary keycodes to work in my existing network of (1) BCM 400 and (4) BCM 50's. All of the existing BCM's allow...

Thanks for the fast response. I have the IP Gateway keycode but not the MCND. What does the MCND keycode allow?

I'm trying to add a used BCM50 to an existing enterprise that already has a BCM400 and 4 BCM50's. We are adding a new location so I'm trying to add the used BCM50 with 7 IP phones. I have already purchased and installed the needed keycodes and I'm able to add the phones to the system. I've...

Morenot, Thanks for the reply. When I received the BCM and 7 phones the IP trunk module showed 80 phones had been registered. I de-registered them but until now never checked the KEYCODES to see if the Keycodes were there for the IP Phones. It says authorized zero. Does this mean what I...

Snowman, Thanks for the reply. I actually only hit post one time. Don't know why is showed up 4 times. Wasn't by intent, but I wasn't able to delete the extras. I tried Manually assigning IP addresses but didn't work, that's when I say on a another board to set the phone to partial DHCP and...

Thanks for the reply Firebird. Port 7000 is opened. I noticed something this morning. When I enabled DHCP on the BCM and changed the Phone set to do a partical DHCP it grabbed the ip address 10.3.51.250 which was also registered in the DHCP lease info tab under Data Services > DHCP > Lease...

Thanks for the reply 4me. I check to make sure set registration was enabled. After reading up on that feature it dawned on me that the phone set never gets that far. It can't find S1 or S2. I was thinking the problem might me my network switch but I'm able to connect to the BCM using element...

I recently purchased a used BCM 50 to add to a new location we are opening early next year. The BCM50 (6.0.2.05.237) and 7 IP phones (2004) cost me very little and since all my other locations are running BCM 50's or BCM 400, it was just easier to have all the locations similar in setup and...

I recently purchased a used BCM 50 to add to a new location we are opening early next year. The BCM50 (6.0.2.05.237) and 7 IP phones (2004) cost me very little and since all my other locations are running BCM 50's or BCM 400, it was just easier to have all the locations similar in setup and...

I recently purchased a used BCM 50 to add to a new location we are opening early next year. The BCM50 (6.0.2.05.237) and 7 IP phones (2004) cost me very little and since all my other locations are running BCM 50's or BCM 400, it was just easier to have all the locations similar in setup and...

I recently purchased a used BCM 50 to add to a new location we are opening early next year. The BCM50 (6.0.2.05.237) and 7 IP phones (2004) cost me very little and since all my other locations are running BCM 50's or BCM 400, it was just easier to have all the locations similar in setup and...

Let me just say two things first. Phone systems are not my primary job funtions. I'm an IT Manager and the phones just kind of fall into my area of responsibility. Second I have found a lot of useful information on this site and wanted to thank those of you who have contribited in the past...

I have 6 locations with a combination of BCM-400's and BCM-50's. We are VoIP at all locations, with PRI's at my two largest locations, and copper at the other 3. Our call center is located at one location with a BCM-50 on a PRI. When they receive calls for others located at other locations...