Search results for query: *

hi All, i upgraded the system from TSW to TSE ver 4.1 SP4 (Mx-one server and classic media gateway including LSU-E and IPLUs)and One Box 5.1 with SIP integration. and now i successfully upgraded the system to TSE ver 6.1 SP0 HF2, but i have a problem with the One Box as following: when I...

Dear Mouafy, thanks for your replay, i tried, but the problem still as it was. thanks,

any help

Dear All, i installed BMS and it was working good, but when the windows update the Framework to 4.0 version the BMS stoped. so when i run the BMS the BMS server window appear normally then Suddenly disappear. i tried to uninstall and re-install it but nothing happened, also i tried to install...

dear all, - I’m using MX-ONE TSE V3.2, and X-Lite softphone. - All data network components are Cisco. - I have successfully registering the SIP extension remotely using the X-Lite softphone(at the internet), and when I make a call from or to the remote extension from or to any local extension...

Dear All, I have new installation for Winseries voice system (Diavox) on Windows 2003 server. The installation completed successfully, and regarding to the installation document I must install Dialogic Patches (service pack 1, feature pack 1, and service utility 66), but I have only the feature...

dear all, The IP network has been installed successfully between MX-ONE TSW SP2 and BP V 8.0, and it works fine. But I’m facing a problem when I send fax from the MX side to the BP side. The parameters used for configure the two sites as following: MX-ONE SIDE:IPLU BPOS=1-0-30...

Dear hdemir, I facing this problem before (283 and 230 alarms), and after many trials I’m find that we have a short circuit in one analogue extension. So please check the analogue extensions carefully. For sure you can try to disconnect the cables from the ELU-29 boards, and then restart the...

Dear Monrovia, If you need to copy the data from the HDU7 to another one you must follow the steps: 1- Block the SCSI port in IPU. BLEQI:EQU=x-x-xx-0; (x-x-xx the IPU or NIU board position) FIMOE:SUBFS=SYSSUBFS11; FIMOE:SUBFS=SYSSUBFS21; IOSIE:NODE=SYSN,IODEV=SYSDISK1; ( Put your new HDU )...

Dear ALL, Sorry every one there is a small mistake in the above procedure: just when you remove your new HDU and Put the original HDU we don’t need to the two commands FICRI so. (Now remove your HDU and Put the original HDU) IOSII:NODE=SYSN,SIPOS=3,IODEV=SYSDISK1,SUBFS=SYSSUBFS11&SYSSUBFS21...

dear, If you loss the data, you must follow the steps: 1-Go to working MD110 BC9 and take the INL (initial load directory) by sent the following commands: Block the SCSI port in IPU. BLEQI:EQU=x-x-xx-0; (x-x-xx the IPU board position) FIMOE:SUBFS=SYSSUBFS11; FIMOE:SUBFS=SYSSUBFS21...

hi rightsaidfred, the only DUSYI command will take long time. My suggestion is to make a PC Regen (Exchange data backup in pc)and replace your HDU ASAP,because if you have a power failure you will loss the data. regards,

Dear all, I tried to install E&M Tie line between two MD110 BC9 exchanges using TLU-80 ROF 137 5406/1 R10B and its working good. And now the customer needs to bind the other sites. Is the TLU-80 ROF 137 5406/1 phased out or not? Can I use the new board (TLU-80 ROF 137 5406/11)? The systems were...

Dear all, I have to upgrade MD110 BC9 system to MX-ONE TSW. Note that the system was BC3 then upgraded to BC9. But please I need to know, what will happen if one of the magazines power board damaged (I mean (3LLO 1314267/1- BFB 101001/1- POU5V 131991/1A)) can we replace it with RG5DC or DC/DC...

hi, Qsig parameters for BC12 MASTER side: ROCAI:ROU=1,SEL=7130000000000010,TRM=4,SERV=3110000010,TRAF=00151515,SIG=311110000031; RODAI:ROU=1,TYPE=SL60,VARC=00000350,VARI=05520000,VARO=00300000; RODDI:DEST=1,ROU=1,SRT=1; ROEQI:ROU=1,TRU=1-1&&1-15,EQU=1-0-00-1...

hi, note VARO in both dest. 166 & 158 158 SL60 H'00000310 H'15420000 H'46300000 NO 166 SL60 H'00000310 H'15420000 H'06300000 NO regards

hi, please: ROCAP&RODAP&RODDP? REGARDS

hi follow the steps to change the HDU: Block the SCSI port in IPU. BLEQI:EQU=1-0-00-0; FIMOE:SUBFS=SYSSUBFS11; FIMOE:SUBFS=SYSSUBFS21; FIOFP:NODE=SYSN; IOSIE:NODE=SYSN,IODEV=SYSDISK1; ( Put the new HDU ) IOSII:NODE=SYSN,SIPOS=3,IODEV=SYSDISK1,SUBFS=SYSSUBFS11&SYSSUBFS21...

hi -You may connect a PC running Hyper Terminal. -Connect your PC to the SIU board, and set the databits rate ,parity and number of stopbits according to the setup of the serial port. -you can now program your MD CIL (Call Information Logging) EDEQI:DEV=SI-0,EQU=x-x-xx-x; EDFII:FILE=name...

hi If you get a busy tone from any external line dial 6 then # (external call back) then wait. When the line becomes free you can get it.