Search results for query: *

That worked perfectly! Thanks very much for all your suggestions ...I learned a lot! If I run into something else I will repost here. Again, THANKS!!!

I do not know of any restrictions for NAT that would be configured on the server. As of yet, there is no security set up on the router. I'll set all that up after clean comms have been established. Just using connection sharing ...no routing software has been installed.

Now I can't get the router to see the DNS servers being assigned by the ISP. Possibly an issue with the ISP gateway?

I added this string to the routing table on the server through a command prompt instead of the reg and I am pinging away.

With this reg string entered, shouldn't a "route print" command from windows prompt reveal persistent routes? Mine is still showing "None".

Route added to the default reg string, server restarted, no joy.

Trying this now ...will let you know the outcome shortly (can't reboot server for a few more minutes). Should I still have RIP configured on the router? If so I want to make sure it's set up correctly. I only have the two networks entered in the RIP configuration (192.168.4.0 and 192.168.0.0)...

The router, switch and both .4 workstations are all new. The windows server is pulling default gateway/DNS information from the ISP and the established workstations are using the server IP for a default gateway (192.168.0.1). The router is not the gateway to the internet. I want to set it up so...

RIP version 1 and 2 (Tx and Rx) enabled for both 0/0 and 0/1 on router. Unable to set static ip route 192.168.4.0 255.255.255.0 192.168.0.254 on router ...it kicked back that it was on "this machine" which makes sense ...sorry for my lack of exp. Do I need to add a physical bridge to perform...

Thank you for responding! I tried the ip route command but I had the wrong IP addresses. I am away from the office at the moment but I will try the correct IPs as soon as I get to work in the morning. I am just using the CISCO 2600 as the gateway and I am hoping that it will suffice. At the...

Please forgive if this post belongs in a different forum. If so, just point me to it and I'll repost there. I am relatively new to setting up "from scratch" networks. I am trying to set up a small office test bed network that includes a CISCO 2600 router CISCO 3550 series switch and 2...

I have installed Corp Edition on a 100 servers and have never gotten a solid answer to this question ...Why does firewall not install on the server. I am not talking about managed server attributes or systemcenter with firwall admin snap-in ...why is there no active firewall installed to protect...

Updtaed 10.2000 to .2001 on server just fine did a client rollout and they stayed on .2000. Even manually uninstalled client and re-rolled but client still on .2000 ...any ideas?

I have a public folder that sees a lot of action. It has built 140k messages since Oct. '04. How can I set the folder to only keep 90 days worth of messages and auto-delete anything older. Also, since there is such a large amount of messages within the public folder, I can not highlight and...

F1lby, Thanks for the response! The clients are all NT 4.0 Workstations. SP6 installed all the way around. DHCP will not give a lease to ANY new workstation when first brought onto the domain. A static IP must be assigned the first time it is introduced. If a static IP is used, the server will...

When I attempt to introduce a new workstation to the domain, DHCP will not initialize with the workstation in question. I must place the machine onto the domain with a static IP and reboot. I then can switch to DHCP, reboot once more, and all is well. This really is no big deal until I try to...

I know normal procedures to place a workstation onto any given domain. Is there a way to force workstation membership from the server? I.E. I have a workstation that has been removed from the domain. The local wrksta admin password has been forgotten or lost. How can I get his workstation back...

the workstation User Manager (musrmgr.exe) will show domain users for local access restriction. >Policies >User Rights... >Click "Show Advanced User Rights" >Scroll to "Log on locally" >Select "Add..." >Select "Show Users" >Choose your user. Ensure the...

All indications are that Backup Exec 8.5 is completing successfully. 100% indication. Time to complete backup is correct. Number of bytes backed up are also correct. When I attempt to restore, the job shows no files or directories. Any suggestions will be very much appreciated. Sooner

Thanks for the suggestion but the problem still exists. One thing I didn't mention in my original post ...I even have an active mouse pointer. The system does not hang. Any further comments or suggestions will be very appreciated. Sooner