Search results for query: *

hey guys, we have a web server for our customers. can you tell me how to config the router so that our customers can access it. the server is connected to one of the switches. our customers can't access the server becuase it's part of our LAN. thanks!

thanks for replying Burt! it's all working now :) one last question...what command to use to separate my networks so that the IP phone LAN don't see the data LAN? thanks again,

it's not routing at all.

Hi Burt, it's not working. what working is the data LAN. I got error message for the below commands: 13-Router(config)#ip nat inside source list 1 FastEthernet0/0 overload 14-Router(config)#access-list 1 permit 192.168.4.0 0.0.0.255 15-Router(config)#access-list 1 permit 192.168.8.0...

hi, I've got a few no go commands: 13-Router(config)#ip nat inside source list 1 FastEthernet0/0 overload 14-Router(config)#access-list 1 permit 192.168.4.0 0.0.0.255 15-Router(config)#access-list 1 permit 192.168.8.0 0.0.0.255 My data LAN is working and still working my IP phones network...

I kind of sum up my understanding, so let me know if i miss anything. step 1 -Router>enable 2-Router#configure terminal 3-Router(config)#ip routing 4-Router(config)#interface FastEthernet0/0 5-Router(config-if)#ip nat outside 6-Router(config-if)#exit 7-Router(config)#interface FastEthernet0/1...

thank you much guys. Our ISP also running our voip phones, so having the router act as DHCP for both networks might cause conflict (my guess). i got Burt's correction, but i don't understand this part of Minue's: Router(config)#ip nat inside source list 1 FastEthernet0/0 overload - what...

thanks Minue! we do have a pubic IP address and DHCP server. another thing we want to do is let the router act as DHCP server for our data network, and our ISP's DHCP server for our IP Phones. is this possible? thank you!

below is my current config: doctor#show running-config Building configuration... Current configuration : 1256 bytes ! version 12.2 service timestamps debug uptime...

thanks for a quick response Minue! how do i config/what command to use to set the interface e0 a WAN port?

here is some more infor. we want to have two networks. one for our IP phones and one for data. the IP phones will be connected to 3500 switches, and the data is connected to 2900 switches. the 3640 router has 5 fastethernet and a token ring port. i was able to assign ip address to those...

we have 3Mbps wireless connection. i am new to cisco, so i know very little. my guess is as long as i can setup a gateway which point to our provider's router and it should work. thanks!

hi, can someone please tell how to configure routing on the 3640 router. i got a card with two ports which will be LAN use. i now need to configure the 3rd port which is the WAN that's for the Internet service provider. thanks!

how can reset it to the manufacture settings?

hi, i got a 3640 router and needing to reset it back to manufacture settings. i'd tried the " no service password-recovery" and "config-register 0x2142" but no luck. it keep showing error message: %error opening tftp://255.255.255.255/cisconet.cfg(time out) help!

thanks Vipergg! and damn you Burt :) I really do appreciate all of your help guys.

Thanks Viperqq! after assign an IP address, should i be able to use a web-based like Internet Explorer to get into it. I'd tried but unsucessfull.

Hi, I have a couple of Cisco 2948G and unable to reset it back to default settings and assign it a name and IP address. I have follow the below steps... 1. Connect via serial to console port (Use these terminal settings-9600 baud rate/No parity/8 data bits/1 stop bit) 2. Turn off the switch...