Search results for query: *

The 3560 is a very temporary loaner. Moved out of a building that is being renovated and I get to borrow it until the work is done. I understand that I can accomplish vlan routing with it but I see no need to reconfigure everything for such a short time. I guess I wasn't clear on the VPN...

Also, you should NIX the RoaS idea and let the 3560 route the VLAN(s) Could you expand on why you suggest this? The only constant in my network is the 2621 acting as the gateway - I am using all other equipment for lab purposes at the moment. BSCI is what I'm working on currently.

Can you tell me offhand what version I would need? I should be able to get pretty much any IOS from work.

I tried setting up a port forwarding and it worked, so at least I can connect from outside now... I would love to setup SSH or a VPN. When I try to setup an SSH I get this: Gateway(config)#ip domain-name test.home Gateway(config)#cry Gateway(config)#crypto ? % Unrecognized command I'm afraid...

The device is a 2621 router running IOS 12.2(37) The config is below. I have my cable modem hooked directly into F0/0. F0/1 is connected to my main switch but the interface is subbed. F0/1.1 is on the vlan where my non-lab devices connect. I am able to to get in an out fine from all network...

Hello, I am having difficulty reaching my home lab over the internet from outside of my house. I have tried using telnet on port 23 and ports 3000+. In both instances I am able to connect from the inside of my network using the IP address of the interface connected to my cable modem, but...

Wow I feel like an idiot! Such a simple solution when I've been trying all kinds of crazy stuff. TYVM.

Just an additional detail... The switch (2950) that i have it connected to shows a green light on the port it is connected to, as does the router. Line protocol is up on the switchport. Seems I should be able to connect..?

It appears that I have a couple of 2610 routers with bad console ports. I have been trying to connect to these routers through various means and I am at a bit of an impasse. When I boot the routers they go through their boot sequence and then start displaying garbage characters on the...

It seems to display normally in rommon. I have had it in rommon for 10 minutes or so without this happening. I have connected pins 1 & 2 and booted - is this what you mean?

I have found another doing the exact same thing. They are both 2610s. ARG!

Hello everyone, I was basically given several 2610 routers to use for a CCNP lab. One of the routers is giving strange characters during the boot sequence. The hyperterminal session then shows no more input or output. The relevant portion is below: cisco 2610 (MPC860) processor (revision...

Thanks for the info. I'm going to see if I can manage to get the latest IOS with IP plus. Any idea how one would go about that?

I have another 2600 that only has ethernet interfaces instead of fastethernet, but it does the same thing. the show ver on it is: IOS (tm) C2600 Software (C2600-IO3-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Tue 07-Dec-99 03:30 by...

It wont take any "encapsulation" command in the config-subif prompt. Is the feature set info in the show version? I am pretty green with this stuff still. My show ver is: Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(6), RELEASE SOFTWARE...

I am certain there is something simple that I am overlooking... I am studying for my CCNA, playing around with a few of the dirfferent concepts with my hardware. I am trying to setup a router on a stick configuration using a 2600 router and a 2900 catalyst switch. I have the FastEthernet 0/1...