Search results for query: *

Needed to re IP the IPoffice once at install location, but not until I had already completed the ignition process on the bench off site. I went into providers, deleted old IP and added new IP of IPO. "put" the changes and rebooted server. Waited and hour and still get the FAILED connection to...

There are mixed select/non-select systems in solution" 1. What does "Set all nodes to select" do? 2. How to change a system back from select to regular server edition? Not sure how or why someone managed to set the 500v2 expansion and secondary server to "Select" mode, but they did and now...

IPO500V2 6.1(22) with 2 combo cards and embedded vmail. Direct dial "quit" working off the auto attendant. I have the direct dial allowed check box and the dialbynumber set on the digit 2. Attendant has been working since this was installed (6.1 so a couple years now). Programming appears...

Server edition 9.4, 9608 sets, trunks are on 500v2 expansion. Default SYSTEM short code 9N/Dial/N/50 gives secondary dial tone just fine. I have user rights configured to point some users to an alternate ARS with different restrictions with a USER short code 9N/Dial/N/51. The 9N in the User...

Moving our secondary server (currently resides in same physical office and subnet as primary server) to a remote branch office. I am thinking I just need to change the eth0 on the secondary server to the new subnet and then remove/add secondary server. I am a little gun shy on it because of...

This is an existing setup I am trying to work out 1 specific piece. Meet me works for creating and joining bridges using the 555xxxx format. When calling from outside to create or join a bridge there is an auto attendant where you can enter as participant or moderator. Moderator leg of the...

Seems like a simple question... but which file do I drop into the "Software Repositories" in the web interface to upgrade the linux box (going from 8.1 to 9sp2). I have the ISO file from the support site. I am thinking I "add" this into the operating system and applications entry then go to...

Adding to an existing network of IP office systems, Hub and spoke config. New switch is 500v2 r9.o.2.o existing networked IPO's are all 406's 5.0(18) I don't want to mess with upgrading the entire network so I was looking to do a simple NON-SCN H323/H450 IP trunk and add short codes to dial...

Cant find any references to these 2 symptoms: 1. When I login and enter password phone seems to login but then sits with "Phone" showing in the top left corner. 2. In monitor H323 status it shows the phone keeps re-registering with the URQ Reason of "TCPOpen" The setup: IP500V2 8.1.73 ports are...

first the docs say you can use an external music on hold source if your server edition has an external expansion unit. I have a 500V2 attached but there is no option to select the external MOH on the primary server. wav file only. This is more a complaint about poor docs than anything...

IPO server edition 8.1, 2 remote offices each with local trunks via IP500 as expansion systems. 46xxsettings filed is pulled at each local office from its respective control unit or server. I would like to use the SET PHNEMERGNUM 9911 option so regardless of where the user is built when they...

Goal is to create a button or feature code procedure to forward all calls to particular DID after hours to an outside number. I have a virtual extension (150) set to call forward off site. Extension is a member of group 100 (this is where the DID rings). trying to get virtual extension (150)...

I have been using local IIS to send voicemails to email through a gmail account successfully for a year. I am using the setup featured here http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ it quit on me and I cant for the life...

I have a Definity and magix neworked together via point to point PRI. On 4 digit dial from definity to magix I get Call ID number, but no name. Magix is release 2.2. How can I get the call ID name to come accross the point to point? I also put this in the definity forum, Sorry for the double...

I have a Definity and magix neworked together via point to point PRI. On 4 digit dial from definity to magix I get Call ID number, but no name. Magix is release 2.2. How can I get the call ID name to come accross the point to point?

I am changing out a comdial system with a merlin magix. I am very familiar with the magix and what it needs for PRI (ATT custom etc) but have no idea if the existing comdial matches these settings or if, for example, the comdial uses NI2 etc. Customer is little to no help. anybody familiar...

thread689-861429 merlinman are you out there? looking for some help with the above closed thread. I am missing the "real" serial number on this MLM007 and need to get into it. Number on the box is wrong.

I have successfully set up vmail to email a number of times and am fairly familiar with the basics. This particular setup is using an email account hosted with yahoo. the outgoing server details are: Outgoing mail (SMTP) server:   smtp.bizmail.yahoo.com Use SSL, port: 465 I can load up the...

I have 2 separate physical lans in 1 building. I have a new file server going in and both lans need access. Can 1 server with 2 nics exist on 2 lans by simply giving each nic an address on the 2 respective lans and then phsically patching them in? otherwise I assume I need a router between...

I am a US based installer looking to intall an IP500 in a trailer (like what you see at a construction site). The trailer will then be put on a boat and shipped overseas. US is 120v and destination is 220V/50Hz. Do I just need a different power supply cable - or a different internal power...