i have an ip403....can i forward my calls to an external no. so that when a certain no. xxxxxxxxxx dials my extension no. it will forward to the programmed external no. and when a certain no. yyyyyyyyyy dials my extension no. it shall not forward the call. in short can i filter the incoming...
i have an ip phone connected to a definity via linksys vpn router. my problem is i am having six to eight second delay before hearing the dial tone...pls help me with this one...
i have an ip4610 phone to connect remotely to my ip403 via vsu5 on the remote side and sg200 on the ip403 side. is there any job aid that i can use to configure my ip phone and the vpn units? pls help..
my fax is connected to a pots extension (on my po 403) and i have to dial 9 everytime i use the fax.is there anyway to eliminete the 9...eg...line auto select in partner/magix...
i want to change the no. of rings for calls to extensions before forwarding to the vm pro. i just could not find the way how to do it...anybody? right now it is 4 rings..
i have a new ipo403 with rel 1.3 and i tried to upgrade the unit but lost it and i tried to connect thru the dte port..i did the at and at-x commands but then the ipo responds with ok and i could not see anything more in the tftp log...maybe i dont have the correct mac address in the...
in my 403, incoming from analog trunks are directed to a huntgroup then to the member. but when the member is rna i want my aa greeting to answer instead of the huntgroup vm...pls help...
how can create a shortcode for direct vm transfer and assign it to a dss button so that i can use the same button to transfer to a user's mailbox by pressing the button and dialing the extension number?
pls help...
i have a magix and i tried to use an analog extension line to connect my laptop pc's modem for internet access...i could hear the modem dialing the access no. then the sound of handshake protocol between modems but then the call will be dropped and the pc would try to redial repeating the...
i want to setup an auto-attendant and main greeting recording on my ip403 release1.3.2 so that incoming outside calls will be ansewred by the vm/aa...any help pls...is it possible?
i have three magixes connected by t1 pri...when a t1 link is down, how do i make sure that my magix t1 module is up and running? is there a local loopback test that i can run by winspm remotely from my laptop? pls help with this one as the t1 carriers are always pointing to the pbx's as culprits...
i have an old legend mail and try to reset a mailbox password but i can't login as administrator. i tried to dial 770 then 0# but i was directed to the operator...i tried 770 then 99# but still can't login...
what is the procedure to login as administrator? pls help in details...
i have a requirement of ringing a group of extensions at the same time but i don't know how... here's the situation...
callers from outside are programmed to be answered by the vm/aa then after dialing "0" or by not dialing anything callers then will be directed to a calling...
i have a t1 that carries 18 did's and the remaining six channnels 19 to 24 used for internet access. i am using a 100r module for this one and is working well.
now i want to adjust the t1 usage to 12 ch for voice and 12 ch for internet...the problem is i cant select the channels on the switch...
in my magix system, i have a did block of 200 to 699 which covers all my extension range but obviously not my calling groups. i am using the calling group 771 and i tried to renumber the group to a number within my did block(from 771 to 466 actually) so people can call the calling group thru...
i have a magix system that i administered by spm from my laptop(external and internal) thru *10. then i added a t1 and that's when i noticed that i couldn't connect from outside the system by dialing either the pots or t1 lines then transfer to the *10... i could hear the modem sounds but i...
does anybody know the maximum distance a magix 4406 phone can go from the magix system? or an 18 button partner phone from the partner ksu? pls help...
i have a magix system with its c.o. lines answered by the auto-attendant. those c.o. lines are also assigned to some extensions and are half ringing the extensions before the auto-attendant answers...any help to get rid of the half rings?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.