Search results for query: *

has anyone configured a Cisco Unified Border Element (CUBE) to connect sip trunks between a SV8300 and a Avaya CS1000? Any assistance is greatly appreciated thanks in advance! [americanflag] Go Army! Tek-TIP Member 19,650 CCNP, CCNA, Net+, Sec+ etc etc

Does anyone know how to factory default a CP-500 (524sg) VoIP telephone? The problem is that is will not load, the lights remain on and will not initialize. I know that you can reset if your phone is active but I do not get that far. [americanflag] Go Army! Tek-TIP Member 19,650

When I started my CCVP track I had a valid CCNA. That was before June 24, 2009 when Cisco changed gears and advised that we needed the CCNA voice as a prerequisite. I now know this to be false because I just received my CCVP on March 15. So I think since I already started the track before the...

Here's the skinny: There was an upgrade from 4.2 to 6.1 all seem to work okay until today. The customer called and advise that four of the five remotes (ccme) intermittently are droping calls from the Unity (call handler). So when a call comes in on the PRI Unity answers and the user presses...

Customer complaining of fxo analog lines dropping intermitently. This happens at differnt time intervals. Lines have been checked several times... some config information flash:uc500-advipservicesk9-mz.124-20.T2 ! voice-port 0/1/1 trunk-group ALL_FXO 64 no comfort-noise timeouts...

After a power failure calls from AA to voice hunt-group not working correctly. Here is the problem. Call comes in and AA answers, You press 1 that goes to pilot 280, the phones in the group ring okay but after the timeout it should forward to an extension (final 230) but instead of ringing...

I have eight AP521G with no controller for uc500 with 11 7921 wireless phones. Can I roam between APs? I have seen several sites that state I need a controller but I wanted to confirm this is needed. [americanflag] Go Army! Tek-TIP Member 19,650

Has anyone installed a Cisco UC500 and integrated it with a crestron home automation system? We are told that we need 7970-G touch screen but what else is needed to complete the install. There is not a lot of information on the web. Any help would be greatly appreciated. [americanflag] Go...

Changed from trunk ended lines on the DTI to a fractional PRI 1-11 and ch24. We can receive calls okay but when we call out there is no audio either way. [americanflag] Go Army! Tek-TIP Member 19,650

I have been told that I will be attending a CS1000E rls5 course in two weeks. I have no experience with this platform. I'm a CCVP so I know about VoIP applications. So my question is what will be my biggest obsticle? What should I concern my self with prior to attending the class. I know...

I spoke with a Cisco Rep this morming and she advised me that if I did not complete the five exams by June 24th that I would be required to take the CCNA Voice exam to certify. Is this accurate? I have seen several blogs stating differnet answers.... Any thoughts? [americanflag] Go Army...

Has anyone setup two adsl 3meg connections and load balance them? If so, how was it done? [americanflag] SPC NVARNG Tek-TIP Member 19,650

Why would a voice vlan 100 be removed from configuration after a power failer... Submit is entered after each program. Other programs such as ip address and trunk ports remain... This problem is on a BES 50FE 12T and 24T.. Any thoughts! [americanflag] SPC NVARNG Tek-TIP Member 19,650

We are receiving stuttered DT for msg waiting indicator. How do we activate the lamp. The switch on the bottom of the phone for neon is not installed... Any thoughts? call manager 6.1 ---vg-224 "SCCP"--- telematrix 2800MW10 [americanflag] SPC NVARNG Tek-TIP Member 19,650

Has anyone here installed Nortel VoIP phones over a Cisco wireless solution? Please advise!!! This could be for a converged voice and data or just voice. [americanflag] SPC NVARNG Tek-TIP Member 19,650

In need of a Multilnk frame-relay configuration. Installed on a Nortel Secure Router 1004 I have two T1's for a 3 meg internet connection with a DLCI of 175 and a WAN/LAN ip address. Thanks! [americanflag] SPC NVARNG Tek-TIP Member 19,650

Has anyone installed a Unified Communications Manager with Percipia? This is for a Hotel/Motel enviroment PMS. What is needed to make it work? [americanflag] SPC NVARNG Tek-TIP Member 19,650

I'm task to setup a Cisco router for a PPP connection from the US to India. I am being told we need to setup our side as E1. Is this correct? [americanflag] SPC NVARNG Tek-TIP Member 19,650

With AT&T using pri type 5ess what is the recommended type to set on call manger? The GW router is set correctly but in CM there are no specific 5ESS paramter. Second question what would cause MGCP to bounce from SUB to PUB every few minutes at my remote GW. My thoughts are that the 1.5 MPLS...

I came across this site and thought it would be helpful to you Cisco and Avaya guys!!! http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/410364av.pdf [americanflag] Spc NVARNG Tek-TIP Member 19,650