Search results for query: *

My DRS link is stable with far end,all E1 data is stable however there is variation on Ethernet connectivity at same link. Receive level is within limits and stable but Ethernet data is cutting..... How to resolve the issue ?

Nortel digital set 3902 went out of service oftenly, I have 7 unserviceable sets. 03 having display problem. How to recover them and how to safe them for future ?

Is there any template available for printing of Alcatel Premium Reflexes 4020 key label ???

I am maintaining Nortel Meridian opt 11c at top of hilly terrain where thunderstorms and Heavy lightening is common phenomena. It is pertinent to mention that my 3 to 4 digital set 3902/3904 had become unserviceable during this type of weather condition. I have installed IDF tag block with...

I have following equipment with power consumption with each. Router = 370 Watt Switch = 520 Watt DSLAM = 70 Watt Switch = 550 Watt How much Rating UPS is required to hold these equipment for 1 Hour ?

I am using 11c switch having 02 cabinet but all ALC(04) card are configured in expansion cabinet. No ALC card is being configured in Main cabinet. Inventory generated, no tone found on any slot any card and any port of card. What is solution ???

I am unable to take backup of Meridian 11c. Whenever i give command "xbk" in LD 143 , its starts Backing up but never completes. Its stuck in middle point

I have Meridian 11C with CS1K , i am facing issue regarding external incoming calls All external incoming calls are being diverted automatically at only operator Digiti which is ext 15. How to fix the issue so all calls are to be recieved on there own sets ?

Hi, I want to restrict specific DN not to be diverted on a DN. There is a DN 5643 , I want to divert all its incoming call to any number I assign except 5641. Is it possible ?

What is safety recommendations for installation of M3902 set. I have installed 3902 at distance of almost 15-18 meter from meridian switch(11C). In last 10 days 02 sets have become unserviceable till now. What are possible reasons and what are safety precautions to overcome this serious issue ??

What is difference between cat5 and cat6 cable ?

What is standard color coding for meridian SL1 XUT card ?

Can any body explain how much voltage are present over ringing and idle phone line ?

I have configured an Analog trunk at port 11 7 and assigned ATDN 5417. It's concern route is 10. I have assigned ACOD 9775 in RDB. When I call on this trunk it shows 9775-1 on display of set(3904 display). Is it possible to show original number from which I am calling instead of ACOD ie 9775-1...

I want to change SSC card of Meridian 11C because of Maintenance terminal is malfunctioning(showing exchange output, not accepting my input). Please guide me if I replace the SSC card should I configure all the exchange or my programming will not be affected ?

Hi , I am facing an issue in Meridian 11C. CLI is working quite well when someone calls internally/lically,but when some external call is received no CLI is working. Please guide.CLS CNAA and CNUA is enabled on every extension.

I am working on Meridian Option 11C which has one expansion cabinet. I have one spare power supply with it. It's expansion cabinet oftenly goes off, And it power up by replacing the power supply. After few days it again goes off and we again replace it's power supply (replace with power supply...

I have opt 11C, distinctive Ringing is "YES" in route configuration,TTBL is "0". When there is an incoming call on network phone set is continuously ringing with a small gap. I want to change this gap with higher "on" and "off" time. How to change ?

Hi everyone, I am Qamar from Pakistan. I want to delete loop, loop 9 is configured on meridian 11c main cabinet slot no 9, but I want to configure an ALC card at this position. I have deleted concern Route,DCH and MSDL but unable to delete loop 9. When I take "inv prt cards" in LD 117 this slot...

I want to configure an analog Trunk and want it's incoming calls to be dropped on DN 3417. I have selected AUTO :YES while configuring it's associated Route and selected ATDN:3417 in LD 14 while creating COT trunk. Now I am calling on my Trunk but it's not ringing on 3417. What is possible reason ?