Search results for query: *

We are getting one of our DID's ported to a cell phone. In the Option 11c can we have the extension that is part of this DID auto-magically forward out? DID = 555-555-5288 Ext = 288 Cell phone becomes 555-555-5288 we would like when someone uses a phone on the Option 11c and dials 288 that it...

My mailbox is setup to forward new messages to email as wave. This works perfectly. I need to forward a message from another mailbox to mine so I can get the wave, however all this is sending is the introduction not the actual message. How would I mark the message as un-read or forward it in a...

Right now we have a number in our Option 11c forward to a cell phone. That cell phone always shows our main number for the caller ID. How do I configure the forwarded ext to forward the CLID info of the original caller?

With CallPilot 5.1 (600r) is it possible to change the voice prompts for an Auto-Attendant remotely? Same as you can for your own mailbox by calling in and accessing the mailbox then recording the greeting over the phone. Can you record the Attendant greeting over a phone, or is the only options...

We have a callpilot 600r. It's been in service since the mid 90's and I'm sure it's in need of some sort of maintenance. hardware seems fine for now, although the HDD throws a message at every boot that says the disk is going to fail. I have 2 questions is there a way to do a purge on the...

We have an option 11c. Currently our PRI's lines are all 780-486-9xxx A new line was just ported into our PRI 780-489-xxxx It was just a signle number ported in. When we call this number it rings through to the switchboard. How do I force this number to a VM box? Do I first tie it to a TN as...

I want to make it so our Call Log has the number with 9 already in front, so we don't have to edit the number to call someone back. I created a new table, Table 1 is the one I created. Table 0 already existed, but doesn't appear to be applied to any routes. Also added table 1 to Route 6, as I...

I'm in the process of moving all the phone lines from a Norstart ICS into an Option 11c. I have quite a few ATA's connected to the Norstar for devices that require regular dialtone. In the Option 11c can I build digital sets/TN's and use the ATA? Or does the ATA ONLY work with analog sets? I'm...

I'd like when I dial out the Caller ID that people see for me is my local DID number, rather than my PRI's lead number... In my system currently setup, Entry 0 allows DIDN - and the HNTN/HLCL match this number. ENTRY 0 HNTN 780 ESA_HLCL ESA_INHN NO ESA_APDN YES HLCL 4869 DIDN YES...

Conversion Utility I have 2 questions regarding this utility. 1. I'm using PUTTY and I'm not sure how to disable BUG, TRF, and MTC. Is that done in Putty's config, or is that somewhere else? So far I haven't seen any of those in the print outs, but with the amount of data getting dumped I could...

I'm porting some DIDs from one system into an Option 11c. I'd like to build the new sets in the Option 11c with Call forwarding already active to the users cell phone. This way they won't miss any class while I'm getting the wires moved, and waiting for phone carrier to complete the port. I...

I'm going to be porting a group of numbers into an Option 11c. The numbers do not currently have any DNs matching in the Option 11c. Will the DN magically appear when I port the DID? Or is there a way to make the Option 11c show some DN's? For example I want to port in xxx-xxx-9122 In the...

Outside of the programming done by the handset I've never done any programming in a PBX. I'm now tasked with porting DID's from 1 PRI to another. The "new" PRI is on an Option 11c, and I need to make it so this system can use the DID's ported in. The telco has already completed the port on...