Search results for query: *

I have a Cisco call manager and a HiPath4000 and an OSV trunked together. The two Unify systems share a branch office for park and the CUCM has it's own park. I am disconnecting the OSV so I am losing the nice park server. If I park a call on the 4K with directed park, I can pick it up from any...

This may be the wrong forum but I cannot find an Xpressions forum I know Xpressions has a numbering Plan in the OSV but where in Xpressions does it reference this NP? I want to change the outbound routing but I do not want to change the existing NP. I would rather write a new one and then make...

Hello, I have a situation where I need to route calls from my 4K V7 to my Cisco call manager. I would like users to dial normally, 9-XXX-XXX-XXXX but I would like it to send 8-XXX-XXX-XXXX to my cisco call manager. I have built the Richt and ldat and I believe the magic would happen in the...

In most PBX's I have worked with I can set up a way to call into the PBX and then make an outside call. This displays either a predefined number or my desk number depending on the system. Is the HiPath 400 V7 capable of such a thing?

Greetings, I do not see an answer in the forum so I'll ask my question. 4K V7 with a PRI that is down. Telco just told me it is because of clock slipping errors on my end. A display of refta below. No X in the supplied column. How do I fix this? DIS-REFTA:CIRCUIT,1-22-9,ALL; H500: AMO REFTA...

Hello, I have a VG202 gateway FXS. I can receive incoming faxes ok but outgoing to PSTN fail. I see in wireshark traces that the RTP packets are being directed to my CUBE loopback address per the cucm in the SDP of the call and there is never an RTP response from this address. I may not even be...

I have a G3SI and I built station 4700 as an X port, type 2500 station. Calls from outside to this number route to Coverage path 47. In Cov Path 47 I have Cov remote 47 to an outside number. I find that I can only have 1 call at a time. The second call gets a busy. How can I process several...

Good day, Does anyone know what this 'Variable Ring Time' And how one might set it? I had a user tell me she was messing with her phone and the no answer ring time went from the system set 13 seconds to 6 seconds. Sure enough, her variable ring time was set to 6. I could not find a way to set it...

Good day, I have searched the threads and have not found what I am looking for. I need to create a PIN that will deactivate / activate an analog extension in a day room. The staff would like to keep the phone in a disabled state until they use a PIN to "unlock" the phone for a patients use and...

I have users that need to disable an analog phone from making calls at night. I do not know the hours yet. I would think that COS switch over would do the trick. How do I set this up? I have 4K V7

Currently my outbound calls from the 4K go out through our OSV. We have a Cisco call manager also and I am routing calls to go outbound through that to the PSTN. I have success with dialing 10 digits but we also want to dial 7 digits. My working LODR is; DIS-LODR:121; H500: AMO LODR STARTED...

Anyone have their 4K tied to a Cisco CUCM? We have a 4K V7 tied to an OSV and we are adding a Cisco CUCM also. I have set 4 STMI's into a trunk group and mirrored the programming to the OSV and was just wondering if anyone knew of anything different for the COT, COT, LODR etc I should be aware...

Does anyone have a CUCM connected to a HiPath4000?

Greetings, We are getting a new CUCM to replace our Unify OSV and I was wondering if anyone used RightFax and if so, do you use a second DN as the RightFax queue number? If your fax extension number is 12345, do you forward that to another number such as 54321 which is the queue number/name in...

Hello, I did not know what the two HG3570's were for in my system and deleted them so that I may re purpose them for a new trunk group. All heck broke loose here and a big lesson learned. Good thing I had a sys dump of the config from a few months ago. My problem now is that XPressions MWI...

Greetings, HiPath V7. I have a trunk group with 4 STMI cards. The second card was downed by AMO several months ago and now needs to just be removed from the trunk group and re purposed. Procedure please? For the sake of programming commands, it is 1-7-1, TG-100. It is going to be part of a new...

Good day, I have a TMANI analog loop start module with two POTs lines for outgoing 911 calling. Is there a way to stop incoming calls on it ..or.. is there a way to direct those incoming calls to a particular extension number?

I have a subscriber that somebody set an offsite forwarding on the extension number. The extension is now available but when I built it to a phone (ip230) when the number is dialed it forwards to the offsite number. I would like to stop this behavior and reuse the extension number. the extension...

Is there a way to call into the 4K V7 and get a dial tone to make a call from the system rather than the home phone? I have Doctors who want to make calls from the system with a hospital caller ID and not show their cell or home caller ID. Can it be secure with an access code so unauthorized...

I have recently moved an IPDA to a new subnet and am having some difficulty getting the APE to connect. Dis-apesu shows the new iP address but no connection. The IPDA shelf is on line with new addressing. STMI's are good. Only issue is APE not acting nicely. I changed the IP addresses in the...