Search results for query: *

Hello can anyone tell me what the code i can use in analogue ext to make a conference call in eMG80 other than using the hook?

Hello, We have programmed T-net between eMG80 and eMG800 which is working fine, After that we programmed an IP network between UCP600 and eMG800. For some reason UCP600 can hear both eMG800 and eMG80. But eMG800/80 can't hear UCP side. Any Ideas?

Hello, We have VCIM connected to UCP100, for some reason when we use the VOIP channel of it to call between UCS clients there is no voice however the VCIM(MCIM) is working normally in case of audio conference.

Hello All, We have programmed ccs but facing this issue all calls are coming only to one HMP port meaning the first call is hearing the welcome message and other calls at the same time only hear ring back tone without any welcome message. Note that all HMP ports are connecting, and registered...

Dears, We are facing this strange web page for 2 LIP-9002 has anyone face something like that, we tried admin, ipkts, lip, leaving them empty) nothing work!

Has any one faced an aralm on UCP "license copy over" what exactly this aralm means?

Hello, Has anyone tried to connect Cisco 7975 SIP phone with UCP?

hello I have an ipecs cm system version 3.0M and i want to upload the license on it. Can someone tell how to do that. I have tried to go to File Management and upload the license file there and then enter putty and write pro -c but the license was not activated. Please advice.

Hello, We have upgarded aria SOHO system to version GS84P-C9Ea_20141208 but after that the stations are unable to pick up an internal call from another ringing station where the person may not be present. Can you please advice.

Hello All, We tried this feature for smdr mailing (image A) and it is not working, will it be possible to make settings similar to voice mail to email functionhttp://files.engineering.com/getfile.aspx?folder=20e685f2-fb89-48f2-80ea-e83472e336c0&file=SMDR.jpg

Dear All, I have the following scenario: System A is UCP100 connecting though SIP Trunk to another system that only has SIP connectivity. The site has BRI lines that is connecting to UCP system. We want when the call reach the BRI lines to be forwarded directly to system B and when system B...

Dear All, i am programming SIP network between UCP and another PBX. the incoming calls to UCP is working fine. But when i try to make a call from UCP to the other PBX it shows on the screen CP GRP 5 busy. Can you please advice.

Hello, Can anyone advice how to program the SIP Ext used for HMP ports when installing CCS with UCP?

Can anyone assist with info on how to setup 2x SBG-1000 with SIP connection. If anyone has documentation please let me know.

We have iPECS MG 100 and we tried to upgrade software following steps in the manual (pic1) with software GS55M25Ci but file couldn't upload we got error message (file upload fail - disk space is not enough) What should be done in this case?

We are facing a problem with upgrading eMG-80 to T1.2.5. Two of our customers faced this problem which is after upload the 2 files GS86M20Be-App and GS86M20Ag-Ker, after the second reset we can't enter to the web admin of the system. We can ping the system but we can't do anything else. We...

Dear All, In LIP-9002 Open VPN category, the telephone is accepting only static IP address. Is there a possibility of entering domain address like LIP-9070?

Hello All, Can u please advise, where we can upload personal greetings for the extensions to activate station CCR

We installed UCP2400 in one site and has 5 remote sites connected through VPN to the HQ. The problem is when remote site A calls remote site B there is no voice but when remote site A calls remote site C it is working fine. We forward the ports and add the router IP address in PGM 132 but still...