Search results for query: *

I have a Cisco VG port connected to a BOGEN PCM2000 paging system. Trying to find root cause to the following intermittent problem. 99% of the time the system works as it should. Dial access code, hear a beep, dial zone number, hear a beep and then make announcement. On occasion though, I can...

I have both AQM & Calabrio One 10.4 call recording servers that I auto record calls to. Using 8841 & 8851 phones on CUCM 10.5. When the phones are on our LAN, call recording works great. When I take the same phone home, connect it to a Meraki Z3 and tunnel back to the office I have recording...

Below is a screenshot of CEQU on a release 7.6 cs1000e. Why is the DCH value shown on some PRIs as DCH 23 and some 24 and how do you change the value. I just added PRI Loop 84 and it automatically set the DCH as 24. I don't recall a parameter in LD 17 that allows me to define 23 or 24. Does...

I’m working on a CS1000e release 7.6 and noticed that some of our 1140 IP phones have the correct time on the phone display however missed calls shown in the call log are off by 4 hours. Is there a fix or patch related to this?

Is there a way on this site to pull up a list of all of the posts that i have made over the years?

My question is in reference ti a CS1000M Release 7.6 PBX. I haven't a clue as to how to work an attendant console as I never get the opportunity to play around with one. Can someone explain the process of an operator setting up a four way conference call (including the operator) then have the...

I hate Cisco, but it appears they are taking over the world. Anyone have any idea where to find a CS1000 Admin job in the Louisville, KY area?

I remember having a gadget long ago that could be connected to an analog port. With this gadget, I could go to another analog phone and call the DN of the gadget which would auto answer the call and give audio feedback as to the number of the phone I was calling from. Is anyone familiar with...

I have a CS1000e on release 7.6. Friday evening I replaced our ELAN switch. When doing so, the system failed over fro active core 0 to core 1. All is running OK, but I noticed 22 input errors when I stat the ELNK in LD 137. Everything seems to be operating normally and the errors are not...

Can someone clarify how a DC switch gets its power in relation to the rectifier and lead acid battery bank? Basically, I'm asking, does the rectifier take commercial power and convert it to DC to power the CS1000 and also keep a trickle charge on the lead acid battery bank which the batteries...

Every time I have to work with a network guy, they always act like they are smarter than me because they know Cisco. It just so happens I know Cisco as well and often have to point out to them where they are wrong. When I try to give them a lesson on NARS BARS their eyes glaze over and they walk...

I need to buy a new drive. Anyone know of a manual that has the specs for a replacement drive?

Anyone have a doc on how to configure a TIE line between Call Manager 10.5 to Ascom VoIP gateway?

I have a CS1000E on release 7.6. I also have system manager, maintenance terminal and PuTTY access. I'm trying to identify the eLan and tLan IP Addresses for the MGU (media gateway utility card) within my MG1010 shelf. Where can I find this info within element manager or thru the maintenance...

It has been my experience that data network guys think they are so much smarter than voice guys however; their eyes always glaze over when you start a nars/bars/cdp/routing conversation. They can't figure it out and then say it's just stupid and over complicated. Then they walk away.

How can I tell from a remote location if a phone has call forwarding active on System version: 10.5? I know I can check the end users Self Care Portal however I would need to know their login credentials. Is there a way an administrator can access the end users Self Care Portal? Is there a...

Anyone know what this causes on CS1K release 7.6? BUG5763 Nil ptr in ISDN_TRK_UTLY. SET_IO_PTRS must be called first, Severity: Minor I been getting reports of one-way audio on a remote shelf. I'm wondering if this is directly related. See attachment for release notes detail. Thanks for your...

I have a phone that has an INTRCPT softkey. It's my understanding that it is used intercept calls from my assistants ringing phone. How do I set this up so it will know who’s phone belongs to my assistant?

I usually set CLS FAXA on fax machines terminated on physical 500 ports. However, I have some phantom 500's that are call forwarded to physical 500 fax machines. In that scenario, should I program FAXA on the phantom port as well?

Can't list the class of service feature FAXA or FAXD in LD 81. I keep getting error sch0101. I can list other class of service features without issue. Any idea why this is happening? I also did a PRT TNB of the PBX and used the pepedog macro and can't find FAXA on the spreadsheet either. Strange.