Search results for query: *

Hi everyone, Does anyone know if Unify has announced end of support for the HiPath 4000 v5? If so, what's the timeframe and where can this detail be found? Thank you!

Greetings, I need to go through some ports to see which are equipped with phones and which have no device attached. Can someone please assist with the RMX command that will help me locate 'unused' digital ports? Thank you!

Hi all, I use CM to complete most MACs... CM is not allowing me to move an analog station and gives me error code: DB Backup in progress. (1013) The DB was backed up using exe-updat:bp,all; and exe-updat:a1,all; (twice each) about 20 minutes ago and the System shows Synchrounous across...

Hi all, I've been asked to pull a couple of CDR records for Inbound calls to a couple of stations during a specific time frame. Can someone please provide some AMO guidance and also how I can pull using Assistant? There is no CDR logger connected to the HiPath 4000 so I'm assuming the CDRs...

Hi all, any and all insight into this is appreciated... i'd like to get some feedback to check if the following procedure may result in a UNIX recovery on a HiPath 4K single processor. The HiPath 4K UNIX recovery procedure documenation i have does not outline this option, but thought that it...

Hi all, I have a problem where the hard drive on a single processor HiPath 4000 v5 went into defect. DEACT-DSSM:A1,1,,YES; followed by a HDCF card reseat followed by ACT-DSSM:A1,1,YES,,YES; recovered the hard drive partitions - controller 1 is active load device. The problem is that the...

Hi all, After a close call on a HiPath 4000... i'd like to get the Xpressions 5 backed up - can anyone provide assistance on best practices / options...? Thank you! ccmjgb - Job 38:36

Hi all, Is there a known method to extract system data & system config from the HiPath 4000's switching unit A card? The hard drive is in defect and will not remain active long enough to do a regen of partition E to get back up. Can the data resident on the active switching unit be backed-up...

Hi all, Just want to collect some input on the proper procedure on replacing an A1 processor card on a HiPath 4000 V5. Thank you ccmjgb - Job 38:36

Hi all, The HiPath 4000 referred to in thread965-1715744 had to have the UNIXware reinstalled and I'm now going through the addition of the LAN component. I've added the customer LAN settings, route for the gateway (metric 2 - unless it should be higher), and added the entire subnet from where...

Hi all, Need some assistance on adding a route that will translate HiPath 4000 internal calls to station 4000 over to 4100 and route over q.sig to cisco - cisco needs to receive 4100. Please provide as much detail as possible (very much appreciated). If this can be accomplished in an easier...

Hi all, Usually make changes on Assistant but it is down. Can someone please walk me through process on changing station names using ComWin? Thank you! - Job 38:36

Hi, How can you find the total of voice mail users an Xpressions 5 is licensed for and how many voice mail licenses are currently consumed? Thank you! - Job 38:36

Hi, What are the distance limitations for the following services on an Option 81 running on 22 AWG copper? digital phone signal (M3903)? analog phone signal (500)? Also, looking to set-up Q.SIG between an Option 81 and a Cisco Call Manager 4-5 miles away. Can anyone please provide input on...

Hi, There is a problem with Caller ID on a digital 3903 w/DN 4001 (example). The name change has been performed using ld 95 and when I called DN 4000, the correct name displays on my 3903. When I received a test call from 4001, the correct name displays on my test 3903. However, when ext...

Hi, I was informed that my Friend's Call Pilot is no longer accepting the admin password via Feautre 983 after a Call Pilot back up a couple weeks ago. The only other thing different was that the HTTP GUI was accessed for the 1st time and I don't know if this would make a difference on the...

Hi, I'd like to ask how to set-up a voice mail account that can redirect a caller to an end user's cell phone based on caller input. For example... an end-user will record a greeting such as: "Hi, you've reached Tek TAC, please leave a voice mail and we will promptly return your call. If...

Hi, I've worked on DR5 & MICS (basic MAC), but I've never attempted back-up or admin using a laptop. 1) I'd like to learn how an MICS can be backed up to my laptop for disaster recovery... ... and ... 2) How can I use my laptop (windows xp) to perform admin on the MICS? I'm assuming...

Hi, FYI... I'm a newbie to Call Pilot 100... I would like to back the config up to my PC. I read through a few threads and discovered that you can access the CP 100 by changing your laptop NIC address to 192.168.110.11 or 12 or other IP in the CP's default subnet - can I initate a back-up via...

Hi, My Friend's phone system/vm is having some issue. I was told that in the absence of a front desk recpetionist, all calls that come in hear main greeting. After main greeting, the General Delivery voice mail beep comes on and takes message. What is now happening is that unanswered calls...