Search results for query: *

Hello team, Wondering if you can help to disable feature 85 on a BCM450, we need to avoid people to use it in the phone system. I have found a section called IP TERMINAL FEATURES nad i have removed the feature 85 but thinking if this only works for IP sets. Thanks or all your help

Hello team, I am wondering if you can help with this issue. I have 2 PRIs with Qsig in my nortel PBX rls 5. and i want to activate TRMB to avoid to use 2 channels.I have set it up but is not working any idea, Your help is really appreciated Thanks :) Route Conf: TYPE RDB CUST 00 ROUT 50...

Hi all, I need to set a new DDP2 card with 2 new DCHs in a Nortel OPC81. But i have a question and i really appreciate your help on this: - How can i know the DNUMs available to set in my DDP2 card?, my understanding is that i need to check the TTY ports and the DNUMs already assigned to my...

Hello team, I need to apply a SYSLOAD on a Nortel OPC81 CP PIV. But i need to confirm if i have to push the RESET buttons at the same time for 3 seconds and then release them or push both INI buttons at the same time for 3 seconds an then release them. could you some of you confirm this...

Hello guys, I was wondering if someone has the manuals for the CS2100 Nortel PBX. I really appreciate your help if you can tell me where i can get these manuals. Thanks in advance.

Hello guys, I was wondering if someone can help me to know the procedure to add trunks h323 in CS1000E rls7.5. I need h323 access ports, right? what packages do i need? What is the procedure to create trunks h323 in the system? What else do I need? Thanks in advance.

Hello guys, I was wondering if someone can help me to know the procedure to add trunks h323 in CS1000E rls7.5. what packages do i need? What is the procedure to create trunks h323 in the system? Thanks in advance.

Hello guys, I am trying to configure H323 trunks in my CS1000 (7.5), could you be so kind to let me know what i need to configure 10 h323 trunks? Thanks guys.

Hi guys, I was wondering how many DCHs i can set in each group. I have an 81c with 3 groups. I really appreciate your help if there is a limit to create DCHs, or install T1s in a group. thanks in advance.

Hello Guys, I need to buy a new DDP2 with a daugther board (DCH). my vendor is asking me about the NTXXXXX number and i don't know what is. I have already installed two DDP2 cards but they have a different NT number: NT5D12AH NT5D12AG do you know what is the difference between them? how can...

Hello Guys, I was wondering if someone has had the next error message. Do you know what this means? the manual only says Path replacement: problem when switching from the old to the new connection. Action: Contact your technical support group. Severity: Critical. Critical to Monitor: No. SNMP...

Hello Guys, I was wondering if someone can help me with this issue. I have a 81c PBX rls 5. and the CDR queue in the PDT is increasing exponentially so while my vendor is trying to figure out how to fix it i have disabled the CDR feature on LD15, whit this we have stopped the counter. This is...

Hi All, I hope you are ok. I was wondering if you can help me to find out next: I have a route with 2 members playing announcements but I want to know how many callers can hear this announcement at the same time. because in my reports i can see ATB (alltrunks busy)status on this route. so I...

Hi guys, I am trying to activate the call forward feature in some analogue phones. But I was wondering if there is a way to activate this service by software I mean through the PBX command line. thanks in advancehttp://www.tek-tips.com/threadminder.cfm?pid=798

Hi Guys, I hope you are ok. I am trying to check if my PBX has enable the future trunk to trunk transfer I only have only one circuit TIE in which I want to receive a call and after thtat transfer it in throught the same circuit to another party outside. What do i must to check to confrim that...

Hi guys, I was wondering if you can help me. I have a thru dial service by last name. My question is how can I update the list of persons in this thru dial. THere are a couple of persons are no longer working here and I want to delete them from this list. btw, the thru dial block is in the...

Hi guys, I as wondering if someone can help me to know the meaning of the trunk utilization % column in a tm report. You know I have in a busy hour 457 in the all trunks busy column but the trunk utilization % shows only 77. I want to understand this field. Is there a tm reports manual...

Hi Guys, I really appreciate your help to know, how many T1s I can configure in an opc81C with 3 groups? Thanks for all your help. Thanks

Hi guys I have a problem with my TM, this one is missing time lines and showing 2 minutes past the hour. This problem started on august, 2012. before this date it was working ok. Any ideas? Thanks

Hi guys I have a problem with my TM, this one is missing time lines and showing 2 minutes past the hour. This problem started on august, 2012. before this date it was working ok. Thanks