Search results for query: *

When using a 1165 phone, when you hit the shift to key, to use key 10 to make a call, is there a prompt in the class of service to change so when the call is done, it goes back to the first page ( key 0 ).

I need to replace 4 batteries which are attached to my old 13 cabinet. can I do this live.

Does anybody know where I can find a NTP on the avaya Web site for a MG1010 Cabinet. What title did Avaya put it under?

Does CS1000 7.5 support analogue trunks.

The time on my new 7.5 cs1000/cppl system increases by 30 min. each day. We log in to ucm and chg the time and a day later it is 30 min ahead. Any suggestions.

How do you build the tty ports on a cppl card (cs-ss-mgs)card. tty 1 is built as cpsi port 0. when I try to build port 1 as a cpsi it tell me only one port can be built. Any ideas. The front of the card says tty 1 and tty 2. Thanks

I have a MCK Analog Extender 1000u. When I set it up in my switchroom and test it it works fine. When I go to the remote site and connect it I have problems and it does not sync up. The remote end is a DSL line with a analog phone working off of it. The DSL filter is connected. When I unplug the...

How many TMDI cards can go in a Nortel MG1010 Cabinet. can not get any of my Tmdi cards to enable after slot 5. All 10 slot in the cabinets have cards.When a do a slft test it fails, I have changed out the cards and rolled with known good one. When I give the command to enl tmdi x fdl or just...

Does any one no where to get the nai.files for 7.50Q unified communication manager on the avaya web site. I need to do my deployment and upload the software.

When programming the DSPs on a MGC card, I believe (zero)- the top portion of the card - is high density. A 96-port daughter board would be programmed as: x x 11 and x x 12 and x x 13. The lower port - for low density - would be: x x 0. That leaves slot 14 and 15 for Virtual DTRs. My question...

i have a callpilot 1005r. When I try to open internet explorer to go to the callpilot manager screen iI get a message server unreachable and its white. What should I do.Thanks.

Does anyone know where to get these, part number is CPC #P0740421 or have something simular to use to label M2616 AND M2008. THEY HAD 12 ROWS ON THEN AND THEY WERE GRAY. THANKS.

I just installed a 201i callpilot (rieninstall) I put image cd 1 in and then 2 and then cd 3. It 100% completed and did it reboot. The machine loaded and end up at the Windows 2003 page and just sit there . Does anybody know why this might be happening. Thanks

Okay I checked the programing osp and isp and ldta are programed. The card is set to loop and after making a call on the BT turet we get a off hook condition or reorder as some people may say. The call are all overseas. Does anyone think changing the signal to ground will work. Please advise.

How should a line side 500 port be programed.Sometime we do not get disconnected and get a reorder or buzz on the card. The card is set to loop and connected to BT Turets.

I HAVE TWO OF THE NTAK11 OPT 11 CABINETS THAT ARE RUNNING RLS 5.0 SOFTWARE. THE MGC CARDS ARE REGISTARED AND I CAN MAKE CALLS. I CANOT TALK TO THE EXPANSION CABINET.MY CABLES ARE AS FOLLOW. A TLAN AND ELAN CONNECTION FROM 1E AND 2T FROM THE MGC CARD TO THE CISCO SWITCH FROM CABINET 0. 1E AND 2T...

How do you get the install menu on a cppm ss to display so you change all your IP address?

How do you change the IP address on a Nortel MGC card. CTRL OAM ask for a password and the passwprd I have does not work. Is there a way to set it to default?

Can not bring my Meridian Mail messages over to call pilot. error 16 . Data came over and all but 3 mail boxes. Every time I try to bring over messages it fails. Any Ideas?

IOD365 Data send failed, retry timeout, addr=192.168.2.65, sCount=3, rCount=0. IOD370 192.168.2.65 Trying to sync up to tm and keep getting this error. How do I solve this.