Search results for query: *

I have an IP500 V1 system with R5.0 (8) currently installed. If I upgrade the system to R7 will the embedded voicemail be included? Thanks

IP Office 403 System. Using 4412D+ phones. I have configured several IP Office 500 systems with no problems. I have recently had put a IP403 system into service and noticed that when I configured the button programming for each set to have 4 line appearances, the phone sets do not allow you to...

I have 3 M7310 phone in a restaurant that is very noisy. The staff is complaining that the volume is too low on the phones to hear. I have explained to them how to turn the volume up on the phones. Is there a way to keep the volume on high? It seems to default middle way every session. Does...

Where would I go to configure the system to allow two phones to use the same external co line that appears on both sets at the same time? Currently the system will not allow but one set on the same external line at a time. IP Office 500 V1 R5. Thanks.

I have several new (old stock) 4624 IP phones. I have set up one of the phones which attempts to load but will get to loading and save b20d01a2_3bin then restart. Then will start all over again. After several loads it will display File Transfer Failed. Last two lines in the TFTP log Tuesday...

Hi, is the pin-out from EU24 to a phone straight or reversed? Thanks

Will the 4400 or 6400 Series Phones work on IP Office 500 R5? Thanks

I have a 4621SW IP that I am trying to setup. I have set up several of the same phones for the IP Office 500. When the phone starts up I press * to program, I press # several times to get to the Command Prompt and try to clear the phone (mute or hold 2 5 3 2 7 #) but it does not respond to...

I have a CICS 6.1 System installed. Most of the phones on the system are T7316E. I have installed a few M7310 phones in a warehouse where they should hold up better and I don’t have to worry about the labels coming off. The LCD display will adjust from 1-9 but regardless what port on the...

Hi, I have a BCM450. I started the unit up and tried to connect to it via the console port. I have configured the computer to obtain an IP address automatically and restarted it with no success. I have also went in and set the computer to have an IP address of 10.10.11.2 and subnet mask of...

I have restored a Flash VM and set up the greetings and 2 of the 4 users have set up their voicemail so far. Currently I have one problem with the system that I had 3 years ago and I am not sure how it was solved then. 3 years ago the business had 8 7310 phones and I changed one 7310 to a...

Hi, I have a CICS 4.1 with a 4 Port Flash 2.0.10 installed at a business. The system has 5 lines to ring and appear on all 10 sets. AA is set to answer on 4 rings. Here lately the system will have a call coming in and will be picked up at the first ring by the system or voice mail and when...

Hi, I have an IP Phone 2004 Model NTDU92. I am trying to configure the phone. When I apply power to the phone I strike the four soft keys to get into configuration. When I get into configuration, first setting that comes up is EAP Enable. I select 0 for no. The phone then restarts and that...

Hi, I have a BCM400 3.7 with 2 modules so far. 4X16 and a DSM16+. What would be the appropriate dip switch settings for the modules? I will be adding an ASM8 module in the near future to this system. I would just like to get the system up and running. Thanks for any help.

Hi, I am replacing a MICS with a BCM400 3.7 Win NT system. I have installed several Norstar systems in the past. This will be my first BCM installation. This system is in use by a business with 4 CO lines and 25 Digital sets. The business will be requiring remote IP phones at a later time...