Search results for query: *

Hi, I have this config on a cisco 881, but it is broken. I want to know if is it possible to re-create this config on a router Cisco 2621XM with 3 Ethernet interfaces : Current configuration : 5306 bytes ! ! Last configuration change at 14:24:25 EST Tue Dec 9 2014 by rene ! NVRAM config last...

Hi everyone, is it possible to setup at the same time, bridge mode in on antenna and access point for internal use on the other atenna ? Thanks

Hi everyone, I have a site to site vpn up and running. At one end I have a PBX for IP phone (SIP). All is working when we are inside (both side of the VPN). I can connect to my PBX and make phone call. But now, I have a client want to be able to connect to the PBX from outside. I said no...

Hi, I'm looking for to see if is possible to block the time per day each mac address can go on the internet ? I saw that some cheap router like Buffalo did, but I have a 2610 for principal router. Thanks

Hi, I will have an internet connection with 2 public IP with it. One will be Sattic and the other one will be dynamic. The static one will be connected on PC alone ant the dynamic one will shared internet for 5 PC. What kind on router that I need to do that ? Thanks

Hi, I have an issue with my 2924 XL. I try to broadcast movie trhough my home network and I have a lot of lag when I'm connected on my 2924XL. When I connect directly on my PC I have no lag at all. Even a realy big file. this is my config: version 12.0 no service pad service timestamps...

Hi, I Have a Cisco 827 that is running fine for about 10 minutes. After this time I begin to have a ping timeout. I change my cable, change port in my switch and connected directly on my laptop, same issue. Thanks in advance. Here is my running config : Building configuration... Current...

Hi, I have setup my Cisco 877W. But I cannot ping my LAN from my WLAN and WLAN from LAN. I post my config if anyone have an idea. Thanks in advance My config. version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service...

Hi, I have a Cisco 1605R. When I download through the router it download only at 50 Kbit. When I download directly, without go through the router, my speed is at 500 Kbit ! If someone have an Idea ? This is my Running-Config : ! version 12.3 service timestamps debug uptime service...

Hi, I have a DSL at home that it work with a SpeedStream 5200 provide by my ISP. I want to change it for a Cisco 827. I had a lot of trouble to find the information about the config of my ISP. Finally I have the information that it needed. After some long evening of test, read end post on...

Hi. I have a Cisco 827. I try to write this config : mmi polling-interval 60 no mmi auto-configure no mmi pvc mmi snmp-timeout 180 Then I do conf term, after I try these command and it said command not reconize. any one have an Idea, my ios version is : 12.2(4)YA11. Thanks

Hi, I have a PIX506e, I want to forward all incoming SMTP (Port 25) to an external address. This is a Barracuda Spam firewall. After the successful scan he send back the E-Mail to the PIX but on the Port 26. I create a static for the port 26, and put the 26 as listen port in my mail server...

Hi everyone, I Have a mail server (Argosoft mail). I have 3 domains on it. I had a LinkSys Wrt54G, all was working fine. But the LinkSys is not stable as a Pix 506e. Then I decide to install a Pix506e with the same open port. I can receive E-Mail without problem, but when I try to send I...

Hi, I create a VPN connection with VPN wizard with PDM. It's work like a charm. I can access all my network...except my pix itself. How can I access the Pix when I'm connected in VPN ? Thanks Bizz

Hi, I Have 2 pix 506e. One with the version 6.3(5) and PDM 3.0(5). I want to copy this version to my other pix version 6.3(1) and PDM 3.0(1). 1) is it possible to do that ? 2) If yes how can I do that ? 3) If no where can I get the last version of the ios and pdm for my pix ? Thanks Bizz

Hi, 1) I'm looking for a way to do port fowarding from outside dynamic ip address to a static inside ip address. I read the command statc can co port fowarding but it seems only for statc address. 2) Is it possible to have an inside static ip address in a DMZ with the pix 506e...

Hi, I have a Pix 506e factory default config, My version is 6.3(1) and the PDM version is 3.0(1). When I type in my web browser : https://192.168.1.1, it's work, ask me a login and password, I have nothing then I click OK, after a have a popup, and ask me again username and password, I click...