Search results for query: *

Hi All, Has anybody come across thier array battery disabling for their Signaling Server's? We have HP DL380's G7 and I'm trying to see if there is a way to get the status of the batteries via the linux cli. I have tried a few commands but no luck. Thanks in advance Jeremy

Hi All, We are migrating off our PBX and over to CUCM. In doing so, I'm trying to test our Valcom overhead paging system using an FXS port. The FXS port is connected up to a Valcom 9940(station Level page adapter) converting the fxs dial tone to 600ohm connection to the 9 zone paging...

Hi All, I'm trying to test an snmp alarms on our new CUCM Cluster. I have everything setup correctly in CUCM and I try to use the snmp set command in CLI. It is complaining about the dash in snmpset -c <community string> -v2c. Any suggestions or idea why this is not working? Thanks Jeremy

Hi All, I started getting this message last Monday, it happened once and then again today. It only happens during midnight routines. The error is coming from an MGXP. I can see that its registered. I telneted to the MGXP and did a joinsecdomain anyway and ran mids again and recieved the...

Hi All, We are currently migrating off our Avaya System and onto Cisco UC System. I have never worked with SNMP. I'm getting ready to alarm a couple Clusters. We will be using V3 SNMP and sending SNMP/Traps to Solarwinds. I have double checked all my config more than once and I still cant...

Hi All, I have received fir0016 and 0017 at 7:15pm the last couple of nights. Performed tests on both the controller and network card, both passed. Any suggestions as to what might be causing this error messages? Its very odd that they occur the same time each night thus far. Thanks in Advance!

Hello All, Do I need to disable the System Monitor card(TTY Port) and pull it out to replace a blower motor? Thanks in advance.

We have a cs1000 7.6 system. Recently we have moved a lot of workers to 2050's. In doing so they were built on virtual loop 224 1. Can you segment out a virtual super loop?

Hi All, Last couple of nights I have recieved these errors. FIJI010 0 0 ALARM 00 - RECVS_FROM 00000001 % % FIJI007 % NEW STATE RING 0: NONE % RING 1: FULL % % FIJI010 0 0 ALARM 00 - RECVS_FROM 00000003 % % FIJI007 % NEW STATE RING 0: HALF % RING 1: HALF I...

Hi All, I have a question: We recently had one of our PBX's INI. Now I get this maintenance message, DA AML :: Info :: AML: 0 MAINT INDICATION TIME, that comes up. I checked AML 0 and it use to be used for the old vm system. See below for the print out. ld 48 LNK000 .stat aml 0 AML: 00...

All, I was looking in the MGC Card and couldn't find any obvious commands under the "help" menu. Can a trace route be performed on an MGC Card? Jeremy

Hi All, We have a CS1000E site that has a Primary Security Server. We will be adding a Virtual DCH and sip trunks to this site. To give us redundancy we want to add a backup security server in case the primary goes down. Its been a while since I initially install this sig server. Are the...

Hi All, First of all has anybody used the NT2K40WA? If so, is there a power board that gets installed on the 2616D as well? If so, does anybody know the part number for the power board? We use to have a 2616D with a on-board NT2K40WA. Somewhere along the line the phone was removed and is...

All, Is there a setting on the PBX or CallPilot to mask/encrypt the password on your CLID of your phone when accessing your voice mailbox? Thanks Jeremy

All, We are moving a site from a location that has a cs1000E using the wall cabinet(old opt. 11c cabinets). I was curious if I could use the 1010 chassi's at the new site and just migrate the existing cards from the opt. 11C cabinets. If I can, is there programming changes that need to...

All, I need to change the DNS IP's for our 201I callpilot. Is it a matter of remoting to the server->right click Network Places->Properties->CLAN->DNS(change here)? Is there a reboot involved? Thanks in advance. Jeremy

Hi All, I have a polycom phone that we were having static issue's with. As it turned out there are 3 dip switch settings underneath the module, which I call a brick. One of the dip switch settings wasn't all the way set. I called Polycom Support to ask what these settings are used for and...

Hi All, We have a CS1000M with one Primary Sig Server. I added the Follower Sig Server. I noticed under the security settings of the follower I couldn't use the admin password of the leader SS to get my security finger print. So what I had to do was use my login credentials to setup the...

Hi All, I'm replacing my signaling servers. I was wondering if anybody has tried to import bandwidth zones and node ID configurations using export and import? I can enter the config manually but it would be nice to import the information. Any suggestions are appreciated. Thanks Jeremy

Hi All, I'm getting ready to update MGC loadware in my CS1000E. when I update the MGC in cabinet with active core(CPU0) will the call server ini? I know it does when they are in a co-res card, just didnt't know if that was the same case in a split configuration(cppm for CS and CPDC for SS)...