Search results for query: *

Hi Guys, I have my VPN server set up on an XP machine at home, when I'm out on the road I can VPN in and see it establishes a connection but throws me back error 721 after attempting to verify my username and password. Road Net 192.168.1.0/24 Home Net 192.168.192.0/24...

Hi Guys, Looking to convert an internally dialled 4 digit extension to a Cisco IP phone over SIP? Following won't go through!? Entry Cnvtyp Numtyp Rou Tardest Pre Trc 1350 0 12 321858 4 DEST DRN ROU CHO...

Hi Guys, I am trying to run a script every day at 17:00 via the scheduler. Now I know the documentation says it should auto open the channel but the script sits there pending until I manually open the channel? Am I missing something here? MX1 V3.2 Thanks in advance! S10

Hi Guys, MDSH> ts_about ====== MX-ONE Telephony System ====== Version: 3.2 SP6 build7 I have a steel type ruggedised analog phone. Once plugged in (even when hook is on) the line opens and stays open until line lock, unplug the line and repeats the same action. When I plug a...

Hi Guys, I have these trunks locked up. (100 1-2 is ok) Cannot roeqe - "Trunk is busy". Any way of resetting? MDSH> susip:rou=100,tru=all; STATUS INFORMATION AT 12:02 30JUL12 ROU TRU TYPE TRAFFIC STATE/PTR LINE STATE/PTR ADD INFO 100 001-1 TL65 CALORG #000E BUSY...

Hi guys, Just wondering the handiest way to divert incoming calls to a DTS to the second line before it goes to the individual diversion number? Thanks a lot, Stroller10

Hi, I have an ADN appearing on a key on DTS. The adn 9889 has a mailbox and diverts to ONEBOX. When a message is left, the LED will not light on the main DTS which also has a mailbox. MX-1 tells me it is sending MWI when I input; susip:dir=9889; Does an additional mew key need to be...

Hi, I have a few 4 digit dest codes and have no problem dialling them from any phone, bar one code, display shows "number barred!". I have checked the cat and matches the cdcat. Number length is fine. Number is set in ED. Any ideas, I have this 4 digit code configured the same as the rest as...

MDSH> extee:dir=63343; Are you sure? (Y/N): y NOT ACCEPTED DIR 63343 HAS QUE. ATS, IDLE, FREE. Why can this position not be deleted??? MX-ONE 3.2 SP2 Thanks in advance. Stroller10.

Anyone know where I could find a 25pin male amphenol for the above system? Thank you!

Anyone know where I could find a 25pin male amphenol for the above system?

Hi all, I have an extension that can only dial internally. But I need to allow it dial external numbers for one hour of the day? Any ideas? Regards, Stroller

Hi, One of our sites is serviced by an LG GDK-100. We don't have remote access. How can I instruct our IT co-ordinator to map a DDI to an extension?? Thanks in advance!

Hi, One of our sites is serviced by an LG GDK-100. We don't have remote access. How can I instruct our IT co-ordinator to map a DDI to an extension?? Thanks in advance!

Hi all, I am trying to log on to our Octel 100 remotely. The details that were left behind from the previous administrator are: 1200,7,1,EVEN I'm using Hyperterminal. I can dial the system successfully but when ###5 is input I hear the modem for approx. one sec and then the greeting is played...

Hello all, I am trying to add a digital board to our system and I'm using CNHUI to tell the system to look for the card, however when I search the card the system says it's assigned but not equipped, am I forgetting something?? Thanks, Stroller10