Search results for query: *

Currently our organization has an Exhcnage server 2007 enviroment, so i descided that we are going to do a migration to exchange 2013. Everything has went as directed with the co-existed enviroment up until a user that has been migrated from 2007 to 2013 tries to login to OWA. When the user...

I have an ASA 5520 that i am installing on an internal network. Using the network 10.36.56.0/21 as my example. I want the traffic to pass through the ASA keeping the same internal address on the LAN. would the following static NAT command allow me to NAT the entire subnet? static...

You will have to bear with me as its been a while sine i have setup L3 on a switch (5 years). I am workingg with a 4506-E with a 6l-e sup. I have nothing hooked to the switch at the moment. When i isses the ip routing command it takes the command but does not place it in the running-config...

I have a 4510R with redun. power supplies (2800 watts) both connected to an APC UPS. Well over the night our APC died. Problem is i only have 1 240 30 amp plug to run off of until the new UPS arrives. Will there be any problem only running the 4510 off 1 power supply? It seems to be running ok...

We currently have 28 Cisco 3560-48PS switches running IOS 12.(25)SEE3-IP-BASE. We recently had to open a TAC case on one of them, and through discussion with the Cisco tech, he recommended upgrading all of these switches IOS to version 12.2(55)SE5-IP-BASE-CRYPTO as the version that is running on...

I installed a Cisco 4510R switch into our datacenter a little over 4 years ago. As you can see by the picture I have attached, the switch has never been powered cycled since its install. The only thing that has been done to the switch every now and again I’ll swap SUP engines, but that has not...

Topology: PSTN>>>>>SIP Trunk>>>>>CUBE>>>>Call Manger>>>>>>AA When someone calls a DID that is pointed to an AA, the caller can pick an option off the menue and the AA will route the call to that ext. When the receiving EXT recieves the call it go straight to dead air. If you call a DID on the...

I have two networks attached to a Cisco 2811, 10.36.0.0 and 24.154.0.0. Currently i have the gateway of last resort set to the 10 network. With the last resort being set to the 10 netowrk the 24 netowrk is not reachable. If i change the last resort route to the 24 network it begins to work and...

Is there a methode using a translation or transformation pattern to where when a user dials example 5551234 the CUCM can insert the area code before it send it to the carrier? Currently the user will dial 8 to go out the PRI so: 85551234 so in the end i would like the carrier to receive...

Currently my company has been given 2 SIP trunks (inbound & outbound) as a promo from a local cable service provider for us to do some testing and consideration of a switch from the PRI. We currently have CUCM-BE Ver. 7.1.5 and a 2811 VGWR cable of acting as a CUBE for the trunks. What I need...

Is there a way either through the Call Manager 7 or VGWR to reject calls from a party that have an "unknown" or blocked caller ID?

I am wanting to deny access to internet on a few particular VLANS on my network and was wanting some input as to weather the following access list would do the job. access-list 112 deny tcp any any eq www Thanks in advance for the help.

CUCM7 When a user is dailing a call if he or she pauses longer than 3 seconds while dailing they get the "call can not be completed" message. Is there any where in Call Manager to extend this time limit? Thank you in advance for your help.

We are currently using Cisco Unified Communcation Manger Business Edition 7. With Unity Connection and Call Manger running on the same server is there a CLI command you can use to reboot only Unity and not call manager. I know you can reboot Call Manager and not Unity but was hoping it worked...

The problem we are having is... Our company used to be on a hosted CUCM, so finally we migrated to our own CUCM. Everything is up and configured and working great except for outbound caller ID. We have an AT&T PRI and when we call any phone that has AT&T service, the call id info is shown...

We are currently in the process of deploying a CUCM-BE7 call manager with 7941,7961, and 7911 phones. When the phones are booting they act like they are going to upgrade, but they error out with the message "Load Auth Fail". The phone will hang on this error for a moment and then continue to...

Two years ago our company purchased our complete Cisco phone system (phones, ata, Gateways, POE switches,) we have ran on a hosted CCM and Unity box for the duration. We are now in the process of purchasing our own CCM and Unity box and started receiving the quotes for this. On our inital...

Is anyone familar with a method to use that will allow you to force out the Proxy settings upon user login with a login script.

I currently have a Cisco 3750G doing all of my layer 3 for my network. The switch is configured with with a vlan for each of my four remote locations that are connected back to our data center via fiber: VLAN 36 10.36.0.1 (Server Vlan) VLAN 56 10.36.56.1 VLAN 128 10.36.128.1 VLAN 64...

I am curretly running an EX2003 server on Win2k3, all of my users only use OWA. The problem i am having is there are multiple users that can send an email between each other, and when the reciever tried to open it inside of OWA it kicks them out to the FBA login screen. I can go in and exmerge...