Search results for query: *

I'm trying to figure out if this service policy is working. Does this look accurate? I'm trying to prioritize my SCCP traffic through my L2L. access-list VoIP-Traffic-OUT extended permit tcp 192.168.4.0 255.255.255.0 10.0.0.0 255.0.0.0 eq 2000 access-list VoIP-Traffic-IN extended permit tcp...

Our organization has an IBM H Bladecenter Chassis with six HS21 blades. We are using the default two NIC's that came with the servers and are looking to add two additional NICs per blade. My question is since the blade chassis only has two Cisco switches in it, how will these two additional...

I am testing an HSRP configuration on two 4506s. I have a group of SVIs running HSRP between the two 4506s with a trunk carrying my normal vlans as well as the new group of SVIs. My question is do i need to have them included in the trunk? I am also running EIGRP because i have several switches...

I am just trying to get some clarification about something. I am in the middle of redesigning a fairly large network. I am trying to get the IP structured where i can use summarization with EIGRP. I plan to use routed p2p links on most of my layer 3 switches and routers. My question is what is...

http://networksims.com/ Has anyone ever used this emulator? I downloaded the demo and it is amazing! Very cheap which seems to good to be true. CCNA, Network+

http://www.getcertify4less.com/cisco-vue-promo.asp Could someone verify the integrity of this? I failed my BSCI on the first attempt and another $150 is a hard hit, but i don't want to wait too long between tests! CCNA, Network+

I am trying to configure a US Robotics fax modem so i can remotely manage a Cisco device. I have found this documentation.... http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807955c1.shtml The problem is i can set dip switch 7 to down and factory reset it but what dip...

I am in the middle of testing our SRST. I believe i have everything configured correctly. When i kill the uplink on my switch, the phones swaps to CM Callback Service. I get dial tone but when i make an outgoing call i get a busy signal. The phone line works because i have can call out with a...

We have installed a new 2801 with a fxs card. I copied the config from another 2800 we have. when i go to "see endpoints" in call manager under the gateway, i get Status: Rejected. Any suggestions? CCNA, Network+

Does anyone know where i can find a list of OSPF Area Types with their route types? I have some test prep questions that is asking to match up the route entry symbols to the correct area type. ex:STUB O, O IA, 0*IA, Totally Stubby 0, 0*IA, NSSA O, O IA, 0 N2, O*N2. I can't find any of this...

I have about 5 3560's running EIGRP configured as EIGRP STUB CONNECTED routers, which talk to a core 4506. I am using vlan 1(for now) as a transport vlan. It is a HUB and SPOKE topology with a Metro E ISP. i just plug all of my switches into their switch and they provide me with a vlan so i just...

I have two 4506's that i want to run HSRP on. One of them is my core switch, doing all of the intervlan routing on my network. I plan to have the same configuration on the new 4506. HSRP is very easy to configure, i understand how it works and how to configure it. I'm confused on what kind of...

I have a cisco 4506 running a very old image, cat4000-i9s-mz.122-18.EW3.bin. I tried to upgrade and it didn't take the first time because of my config-reg. so i changed it to ox2102. so i entered boot system flash cat4500-ipbasek9-mz.122-44.SG.bin. It rebooted into ROMMON and said that it must...

Anyone know why you can't ping an SVI after it has been created? I created it, issued no shut and i can't ping it from the switch. I can ping it once i trunk it to another switch. annoying. CCNA, Network+

My cisco 4506 goes nuts every time i turn multicast on. Unfortunately most of my inherited network is on vlan 1, which i'm slowly segmenting. When ever we need to use a multicast application i have to turn multicast on for vlan 1 (ip pim sparse-mode) When i enable it my cpu stays around 80-100%...

I currently have a Cisco 4506 doing my inter vlan routing (About 30 vlans). I have a default route pointing to an ASA5520 (static routes pointing to the 4506) and a default route pointing to our core router then to ISP1. I added a second ISP. I have tried about 10 different solutions and none...

I have a 5520 that is having issues. I have one Dynamic NAT for a few different inside networks to one public IP. Also, included in my block of public IP's i have a few static one to one NAT's. The problem is i recently added another ISP. I configured one of my ASA interfaces with the IP the new...

I have a 5520 that is having issues. I have one Dynamic NAT for a few different inside networks to one public IP. Also, included in my block of public IP's i have a few static one to one NAT's. The problem is i recently added another ISP. I configured one of my ASA interfaces with the IP the new...

Does anyone know if you can have two outside interfaces on an ASA5520? I have two ISP's and i want to have most of my traffic go out one ISP like its been, then have one subnet go out to a new ISP link. I have an inside interface, and outside interface, then a new outside interface. When i debug...

I have a ASA5520. I have a 4506 doing my intervlan routing, static routes pointing to the ASA then out to my ISP with static routes on the ASA. We recently added another T1 line for one vlan. i have a static route on the 4506 just like all of the other routes, on the ASA i connected the new t1...