Search results for query: *

Our Company decided to pull the plug on the Siemens contract years ago so we have been working on an older Rev; 5.0.19 and many of them have been getting stuck in Initialising so I've definately traced it to an issue with phones getting duplicate ip addresses. Has any one else experienced this...

Hi All, I'm trying to setup a call fwd unconditional but get stuck at line F01: ADD-ZIEL:FWD,2901,VCE,80116568762000,"",CFU,INT,SYSTEM; H500: AMO ZIEL STARTED F01: SOURCE STATION 2901 IS UNASSIGNED OR AS AN ACD NUMBER (AMO DNIT) CONFIGURED. Any one know why my station 2901...

Hello, My H3K V4 suddenly decided to drop calls from external callers instead of forwarding to voicemail on no answer. Internal forward is ok. I've had the local Telco check the T1's and they say they get a disconnect from the switch. Any ideas on what could be causing this or what I can...

Hi all, I have an Avaya IP 5610SW phone that I need to set it to a different extension. Is there a way to do this from the actual phone? I was told hold the * down as I'm booting up but that only seems to get me to the IP and system stuff, not the actual extension the phone needs to be...

Hi All, We setup a new (Asterisk) mail server but it's not getting the Redirected Dialed Number Information so there is no way to tell how to identify the redirected number and send it to the correct mailbox. Is there a way to turn on the Redirected Dialed Number Information Service? This is...

Hello, Can anyone tell me which cards support a T1 circuit on the Hipath 3K and if there is a way to find out which ports are in use or not? We currently have the following installed: CBCPR HXGM3 SLA24N HXGM3 STMD8 SLMO24 TMST1 TMGL8 PSU Thanks! ---Mike

Hello, Does anyone know how to check the logs from AMO? In particular, I am hoping to find log data on a certain PEN (pen,1,1,13,1) Which goes to our voicemail server. Seems our VM server MWI (Message Waitin Indicator) intermittently does not come on for users with new voice mails unless I...

Anyone ever do this? Is a DLS Server required? I want to go from 5.0.19.0 to 6x Thanks!

Hi All, I have a Hipath 3000 and use Manager-E software to administer. The system time is off by about 5 minutes, does any one know how to change this? Thanks, ---Mike

Most of our Optipoint 420 standard phones get stuck in init. Has anyone else encountered this problem?

Hi All, I'm currently looking into setting up QOS for our Hipath 3000 (V.4.0).. Does anyone know which protocol / port numbers I should be looking for to mark? Something tells me it's in the H225 family? Thanks!

Hello, We are looking at increasing our capacity with 2 more T1 lines and have already installed the cards but I do not see them when doing a dis-bcsu:tbl; < <dis-bcsu:tbl; DIS-BCSU:TBL; H500: AMO BCSU STARTED ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1...

Hello, Does anyone know how to display trunk group information on a Hipath4000 ? Either through Amo or Assistant? Thanks!

Does any one know how to set a stations caller id on a Hipath 3000 system? I'm using Manager-E Thanks! ---Mike

Does any one know the difference between the DIU2U-M and DIU2-B cards? Also, would a DIU2-B support 2 PRI interfaces? Thanks! -Mike

Can any one tell me the basic steps to configuring a new DID range that I just received from AT&T? Thanks!

I'm trying to configure option 43 for our optipoint 420 phones (Hipath 4000 V2) and setup a voice vlan. My Vlan is 666, however according to the hex converter I use it is 29A in hex so I tried the following: 01 0A 53 69 65 6D 65 6E 73 00 00 00 02 04 00 00 00 29A 00 00 00 00 00 FF Due to the...

Hello, We are currently looking into an inexpensive Disaster Recovery Solution for our DataCenter Servers. The plan is to duplicate the servers at one of our East Coast offices, building a new subnet there. The Servers are mostly for users home drives, shared drives etc, not internet servers...

Does any one know what option in COS could stop incoming calls? Either through the Assistant or Expert mode.. I need to block incoming calls to a station.. Thanks!

Hello, We have a new VOIP server setup just for softclients (X-lite) and connected to a DIU2U-M card. Outbound calls are working as well as internal softclient <--> Siemens phones. We have new DID's to support these softclients and configured in the Hipath4000 (V2) External calls into the...