Search results for query: *

Hi i am getting ERR008 4 0 5 0 8 1 5 4 randomly and call between cabinets got silent or no speech path. Then TN`s are random but this error is between cabinet to cabinet only, with cabinet ext to ext call is OK, it is cs1000e rls 5. Can somebody point a right direction to resolve this?

Can somebody briefly explain what rule should i follow to set VPIM??? i mean how to calculate/describe rule for setting VPIM prefix in Callpilot 4 or 5.?? does it related to DID range i mean lets say i have DID number ranging 5206000 to 5207900 and my extension are bulit from 6300 to 7200...

Hi all, it is CS100E rls 5. its been in installtion phase, i programmed all analog/DLC/IP softphone ext with everything accept Zone, i didnt created any ZOne and all MGC/DB`s are programmed with no zone entered. Today i created Zone 2 and communications between got stop , call within cabinets...

Hi all. Can somebody point me how to upgrade loadware of MGC. I downloaded 6 loadware files of MGC from ESPL site and tried to load these files through Element manager Software--->Upload file but it pop an error that the file syntax should not conatin /, \, % etc and file extension must be...

Hi all, i need some info regarding MGC DSP usage of CS1000E. I mean with different call scenario. Can somebody answer these separately whether DSP is use or not in these call setup. (1) Analog to analog ext call within cabinet or cabinet to cabinet-->DSP is use or not? (2) Incoming DID...

Is there any product bulletin or document or some info about compatibility matrix of release 5 with SSC card and daughter board vintage and flash boot room version for release 5. this info is needed for CS1000M cabinet release 5. I was seraching on Nortel site and found some matrix but not...

Hi all, i have installed a Callpilot 600r release 5 with CS1000M rls 5 with 40 Fax messaging license also. Now to setup Fax messaging(to receive Fax msgs into outlook) i need a CLAN IP which customer dont wants, i mean they dont want some other device on there LAN for some security purposes...

Hi it is 11c rls 24.24. IP`s and sub net mask are set to default in PBX, One PTY was also created in PBX and i can ping PBX from my computer. I tried ZOC and hyper terminal (TCP/IP) to connect but it pops error (i think error is connection refuse, in ZOC port was set 23 and i also tried 25,22...

Hi all, I have a site having system 61c rls 25.40.With following IODU and CP CP , 0 15, NT5D03PB 02 CP , 1 15, NT5D03PB 02 IODU/C, 0 17, NT5D61AB 10 IODU/C, 1 17, NT5D61AB 10 The CPU-0 somehow gots down 2 months...

Hi all, it is CS1000E rls 5. I need to change BT setting of PBX as advised by our principle vendor to get CLID on COT lines, we are using DXUT CLI card to get CLI and didnt get success due to BT settings. Are these setting exist in PBX and how do i set these? BT Frequency = 450 Hz BT Cadence...

Hi all, it is 61c Rls 25.40. We got our CPU0 disbaled/not responding, I inid switch fist but still CPU0 was disabled then i shutdown both CPU`s and again powering ON but result was same, CPU1 was working and CPU0 was disabled.Then i put CPU1 on Maint state unplug CP and IODU of CPU0 and brought...

Hi all, need advice in the following CS1000E ,rls 5 installation.I read NTP`s but they are a bit hard and mixed to understand. PBX spec are (1) 4 cabinets. (2) 185 analog extension,32 digital ext,25 Soft IP ext 3 PRI`s,24 COT lines with Call Pilot 600r and MICB. MWLC cards = 12 DLC...

Hi all, i have a SSC card having Eng. code NTDK20JA, can i install Release 5 software with that SSC card? does it works ok?

I was reading a post about NTP table and some of its commands in LD 117. Can somebody explain what is NTP table and why it is used? Regards

Hi all, i have installed a new CS1000 (on SSC card) release 5 with call pilot 600r rls 5. Every thing is working OK with call pilot. accept i am getting following error on and on. COM001 Ethernet driver: unit 0 is being restarted COM001 Ethernet driver: unit 0 is being restarted COM001...

Hi all i am installing a CS1000e system, i have both DSP daughter board installed on MGC and i created DB32-->4-0-0-0 upto 31 channels DB96--->4-0-11-0 upto 96 channel, All Ip`s are assigned i am getting following error IPMG[4 0] 31/12/2006 03:35:51 LOG0006 SYS: VGW5000 Card initialized, all...

Hi all, could somebody explain what is AST for?? I mean we use AST while setting up Call Center. What they do in call center environment? Regards

Hi all, PBX is 61c Rls 4.5, having 30 COT loop lines, i just upgraded that PBX from old rls 25.40 with complete core replaced. Now i am having an issue of dialing problem on COT lines |(i don't have ISDN PRI in that PBX). Some times when i dial complete number after accessing COT line (No...

Hi all, does some body knows how to implement EANA protocol in 61c rls 4.5. Need a little info to start that dialing protocol. I read NTP`s there is a lot info about EANA(dialing plan NTP) but no info how to implement this. regards

Hi all, it is 61c Rls 25.40. I am getting following error after every 2 or 3 minute. I also checked the TN it is working OK, Any advise??? AUD029 00F0D3E8 00000C04 00000001 00000C85 00000000 00000000 00000008 00000C85 0 0000000 AUD029 00E58EFC 00000C04 00000001 00000C85 00000000 00000000...