Search results for query: *

Hi folks. I might sound stupid but I want to know where in the 1750 VPN router can you change the http password for the administrator. I did change it under Admin -> Administrator but I saw that it changed the password for only the telnet session and I could still log on to the router through...

I have a contivity 1750 router and I am trying to use the interface filters on it to block all http access from the inside LAN to outside WAN. Under current contivity interface filters, there is a "Permit HTTP" filter. When I edit it, it shows me the following rules which are currently in use:-...

We have a contivity 1750 VPN router and we have not purchased the stateful firewall license yet. We want to block all the http requests going from the internal network to the outside WAN. Where and how in the router do we configure that?

We changed the IP address on our CCMA and CCMS server yesterday and we are not able to pull any reports from the CCMA. When we click on a report, it just opens a blank window. We have tried to restart the services on the CCMS. They start and after few seconds, they stop. There are few service...

I had set up "My Documents" redirection for the users in our domain. We only have 15 users with a Windows Small Business Server 2003 Premium Edition. I just noticed that it stopped working all of a sudden 3 months ago. All the new user accounts I created in the last 3 months do not have their...

We have 2 CPU's on our passport 8310 switch. 1st management port IP address is 192.168.2.1/255.255.252.0 This IP is in the same subnet as one of our internal VLANs. 2nd Management port IP address is 10.10.10.8/255.255.240.0 After reading the documentation on the switch, it was recommended...

When I telnet into the switch, it takes me into this mode Passport-8310:5/config/tacacs# How to get out of it. How do I go into the global configuration mode from here? HELP

After doing a soft reset of the switch, I am getting the following prompt when I telnet into it. Passport-8310:5/config/tacacs# I cannot run most of the commands in this prompt. I cannot go into the privileged mode either. I type "Enable" and it says "command not supported". How do I go...

How can I schedule shutting down the computers in an OU by using task scheduler in the group policy Thanks SMahajan

I am trying to put a BAT file which would shut down computers for 2 departments in our company. How could I do it with group policy without using Startup or Shutdown script. I understand that through group policy, it can be done with startup or shutdown script but I want to shut down...

We cannot set up a branch office VPN tunnel between BSR222 and contivity 1750. ->We have selected IPSEC with 3DES and MD5 encryption and ->ISAKMP is enabled on both sides. ->Perfect Forward Secrecy is disabled on both sides. ->The connection type is Peer to Peer and we have setup the same...

There are 3 VLANs in our network and we can assign an IP address to each VLAN interface. While connecting this switch, we connected all our computers in VLAN 1 and forgot to assign an IP address to its interface. All computers in this VLAN are in the subnet (192.168.0.0 to 192.168.3.254) with...

How do I set up an IP address on an interface on a Nortel Passport 8300 switch through CLI. What is the command to do it.

When we bought the switch, we connected all computers in a single VLAN which is VLAN1. Our business needs to add more VLANS and each of them should be able to connect to the internet. VLAN1 has all computers & internet access. The router and the management port are also connected to this VLAN1...

We have a Nortel Passport 8300 switch. I have trying to configure it in the CLI(Command Line Interface) but it is not taking the commands which are meant to be run in NNCLI(Nortel Networks Command Line Interface). Please advise how to switch from CLI to NNCLI Thanks Saurabh

I have two VLANS implemented on my 8310 switch, first VLAN (VLAN2) which has only 2 of the 250 ports on the switch and the other (VLAN1) which has the remaining 248 ports on the switch. I have assigned an IP address of 192.168.6.1( 255.255.255.0) to VLAN2 and have assigned IP...

We have purchased a passport 8310 routing switch for our network and while trying to configure it from the command mode, I found that the access of the switch from HTTP is read only. The command to enable the web server on it is web-server password <ro> <username> <password> I wanted to know...

There is a built in "DENY ALL" filter under the "interface filters" on the Nortel Contivity 1750 VPN router. Although I can edit this filter and allow traffic for both incoming and outgoing directions, I cannot delete this filter. When you try to delete it, it says that the...

We have a Contivity 1750 VPN router and we are trying to set up internet access from it. There are two ethernet ports on the router. LAN0 and LAN1. The router gives us the ability to make either one of them a public or a private interface. So we have configured our WAN IP address on the public...

Does contivity 1750 VPN router support URL filtering. If yes, where do you set it up from. Also is it possible on this router to track HTTP access for a particular IP?