Search results for query: *

Have a 3300 MXE using 7.1 that has active voicemail boxes but call forward to voicemail is not acting right. If an internal call is no answer/busy the call forwards to voicemail but to you're own voicemail box and not the person you are calling. External calls end up in auto attendent. I...

we have a 200 mx connected to a POE switch. The client has a metro fiber ring and right now have 3 locations on it. They are using on controller for all locations and decided to put a vlan up on each of the hp procurves. Their IT guys set up the vlan up themselves. At the location with the...

Category Name Faulty Disk Alarm Level Major Total 2 Unavailable% 50 Minor Threshold 50 Major Threshold 50 Critical Threshold 100 Does this mean one of the hard drives is faulty? I believe that it does and if so the system will...

Got another situation here. We are using prairiefyre 6110 customer contact manager software to deliver call accounting reports to the client. In some reports the numbers appear to be inconsistent. What we found out was that in prairiefyre calls after 5pm are counted twice. The only change that...

Have an issue with call hold timers. in the class of services we have them set to various times. ACD has 360 before ring back, some have smaller hold timers, what's going on is that calls are ringing right back all of a sudden. We have two switches, one is the primary and the other is just a...

We have two console- attendents at a location and there are having an issue with night mode being turned on before closing. Now when someone call XXX-1000 one or two of the attendents (ext 1513 or 5001) will answer the phone. They are using the 5550 console sets plus the PC application as well...

I had a service call to extend a demarc from a telco room to the customer sweet. What I found was a DDM2000 with a DSX panel that terminated on a 66 block. From my memory when dealing with T1s is that 1) there is a smart jack to plug into or 2) a CSU/DSU to plug into. What happened was a tech...

we have a 3300 on site and i want to put in a route so that when someone calls xxx-1200 it will route them to the vmail box in the 3300 from the 200. I just need a little bit of instruction on how to make that happen. I was able to add 1200 to the form but beyond that i'm trying to figure it...

I have a Mitel 3300 MXE with 7.1 software. It's going to replace a LX at a client location. My question is do I have to install the software on the primary HD before I install the RAID controller? "CAUTION: You must install only the first hard drive, with the installed software, before you...

My vpn client connects perfectly to the PIX 501 but I am unable to ping anything at the host site. The dhcp subnet at the host site is 192.168.0.2-192.168.0.129 and the vpn range I assigned was 192.168.0.130-192.168.0.140. My vpn client recieves 192.168.0.130 but I cannot reach any device on...

Is it possible to install an operating system on a pc with no optical drive? It is possible to do a network boot with my motherboard but can I in turn browse to a shared dvd drive and install from there?

I have a geforce 7800 with a vga and dvi output with a monitor connected to both to set up dual monitor. When the pc cuts on i see preboot information on both monitors all the way to the windows loading screen, when it's time for the login screen to come on the dvi monitor says no signal. Now...

I have a pix 501 with one public ip address and a few servers behind it. one server is being accessed via rdp and the second needs to be accessed on port 21000 udp static (inside,outside) tcp 70.43.148.82 3389 citrix 3389 netmask 255.255.255.255 0 0 static (inside,outside) udp 70.43.148.82...

Our 3300 mxe has been configured to page through an external paging system. dialing 70 will dial an access code, when we hear a tone we type in a paging zone id... (01) for first floor. At this time we can get the notification tone over the paging speakers on the correct floor. Now the pager...

static (inside,outside) tcp external_address 21000 GPS_SERVER 21000 netmask 255.255.255.255 0 0 Does having the netmask set to 255.255.255.255 limit connectivity to the internal device to one connection at a time? And if so does setting it to 0.0.0.0 allow unlimited connections?

in a sx-200 icp what form gives you a listing of all the trunk groups on the switch. i need to verify if all the incoming/outgoing smdr is turned on and that all he trunks are smdr enabled.

Is this good so far? I would like to be able to route access from any outside host that uses port 2100 to a specific internal host. pix(config)# sho access-list access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 256) alert-interval 300 access-list...

2 T1's run B8ZS ESS and need to BCCIII Card. Do not have a T1/E1 module for ip. Using per nodes. Any suggestions on how to make this work without changing the actual T1's which take up to 30-45 days according to the service provider.

Customer had 1 pix firewall connected to 1 t-1. Now they have 2 t-1's and will be getting a range of ip addresses. Now we have been using it because it's easy to configure but now a bit of brain work for non cisco experts come into play. Question. what steps do i need to take to 1. configure...

Having success with establishing a connection between modems but the characters that are showing up in hyperterminal looks like this... €ø€ø€ø€ø€ø€ø€ø I'm using the same hyerterminal window i use with direct connection. I'm using an US Robitics Sportster faxmodem with x2 all dip-switches...