Search results for query: *

Now when I managed to configure the PBX to transfer the original A number, there was a problem in the case that a number is not received(provider does not send the caller's number). In this case, the PBX "sends" B number, on which redirection is made. Then the mobile device shows country code +...

Hi! Is there a possibility to send OD number for A-number(calling number), if is a operator call outside the sistem? Problem is this: We finally managed to arrange with the mobile provider, to transfer original A number. We organize everything, except Caller ID of operator. Now, if a operator...

Hello to all! Is there a way to change the size of the bandwidth usage on IPLU board? Now every call use 64kbps, in maximum usage on IPLU board, I need 2048kbps. So, my question is how(if possible)to decrease "kbps" per call? I looked at Alex, but I have not found anything related to it. Also...

Hello to all! I have one question. We(my company) wants to buy IPLU board for connecting remote users. I want users to use analog phones. On the other side(over the network) we have Quintum ATA(Quintum AFG200, with H.323) and Cisco ATA 186(with H.323 firmware). Is it possible to use that...

Hello! In my company we have two PBX, which are connected with each other over an IP trunk. Speech(voice) over IP trunk works normally, but the problem is when sending a fax over IP. It is probably necessary to activate QoS, but it costs money, and it does not come into consideration now...

Can anyone describe the exact sequence of commands to upgrade NIU/NIU2 board? I use MD Disk Tool to copy the firmware on NIU2 board. If I remember correctly, I need FICRI command and the CNBRI command or something like that? So if someone can write the exact sequence of commands, I would be...

Some time ago, I sent a question regarding CIL. I have not received any response, :-( I am interested in how the data is sent to the accounting program. Commands that I have set the following (CIL over Ethernet): IOEQI:IODEV=CIL-ETH,EQU=1-1-22-4,TYPE=NETWORK,USAGE=OUT...

Hi to all! I wondered, is it possible to "split" IPLU board in way to use half of board for IP trunk(we have IP route with another MD110) and half of board to connect IP phones? Thanks for all useful tips and answers! bb34nne

Hi all! Is it possible to turn off external/internal follow-me trough WinFIOL? I know that it is possible over the phone, with #22# or #21#, but if there is command for it I would appreciate that someone reply how to do this! Thanks in advance bb34nne

Hi all! I have another question: when initiating a boos-secretary set, on what things I have to take care? I know this, I initiate extension with KSEXI(both phones are digital), with KSMDI I program keys for control of extensions, and there are BSEC function(I think I will not use this, I will...

Does someone know which batteries, model of batteries can work with MD110? System is CXP1010101/4/TSWSP02/R3A, 1 LIM, 4 magazines. Batteries that I have in exchange works only 30 minutes when is a blackout. bb34nne

Hi all! I have problem with group pick up. I have set group, but I don`t know how to assign service code to group call pickup. My system is TSWSP02. What is the command for setting service code for group? thanks bb34nne

Hi all! I have simple question for you all. I think. I want to transfer 1 analog line from my PBX(Panasonic PBX) from one location(location A) to another location(location B) over VOIP. When someone lift the headset on location B, automaticly get signal from PBX(location A). Do I have to use...

Hi all! Let me explain on example: I have 1 ISDN number which is connected to PC. On PC I use Asterisk and from Asterisk call goes over VOIP on the other side(it doesn't matter where). When I call that ISDN number, I use "post dialing" to dial number on Asterisk. I want to restrict use of that...

Hi all! Can someone explain how to connect BS330 station on ELU31 board? How many pairs of wires do I need? I looked in Alex and I found that station use 4 wires. 2 for power, and 2 for data. What position on ELU31 board is for power, and what is for data? And how to correctly connect wires on...

Hi! Can someone write here how can I set code for DISA calls. I want to set code when someone call DISA number from outside line, first they have to enter code and then(if code is correct)dial number. Now I have DISA but with no protection. Thanks bb34nne

Problem is this: I can`t track incoming and outgoing calls to DEST or from DEST with CIL prog. I tried to change formats in CLOHI command, and problem is still here. This is example of lines that I getting from exchange: 02280724 0075 DDDD 8389998373 00 093001005...

Is it possible to create 2 CIL outputs, one on RS232 and another on IP at the same time. I want to try another soft for gather information from MD, but 2 softs have to run parallel in the same time. thanks for answers bb34nne

How to create 2 routes on one E1/T1 connection? Now I have 1 route(trunks 1-1&&1-31), is it OK to initiate another route on trunks 1-25&&1-31? Will it work? Do I have to do something with signalling? thanks bb34nne

Hi Can someone post exact commands how to set Least Coast Routing for international calls. I want to set my international calls to go on route 70, and then on route 1(CHO=1). How to set tables? This is what I got now on exchange: LCLDP:LIM=ALL; LEAST COST LIM DATA LIM AC DEST 1...