Search results for query: *

I would like to capture the source IP of anyone logging into one of our Meridian 1 or CS1K systems via rlogin. I thought this might be an SNMP trap, and it certainly may be, but when I configure an open alarm in 117, I get a message that someone connected and logged in, but I can't see the...

I'm trying to set the data VLAN ID via a system.prv file or via Nortel-i2004-B string in my DHCP server. The IP Deskphones Fundamentals book shows dv=60 on page 447, but I can't get that to work. PCs plugged into my 1210 set jump right onto my voice LAN and ask for an IP address. When I put...

I haven't setup auto provisioning before, but do have experience using full DHCP. I've read the section on auto provisioning, but it leaves a lot of questions, which is why I'm here. I'm trying to start off simple and add configuration as things go well. I haven't gotten very far, but maybe...

Perhaps someone can give me a pointer or two to move my project along. I'm trying to use an Asterisk box as an inexpensive conference bridge. I don't have any connections to the Internet, or any other publicly accessible vulnerabilities, so security is NO concern. I'm completely TDM to the...

The majority of the systems we deploy are stand-alone, meaning not networked to another call server/PBX. Now that 7.5 is upon us we are reviewing our options for deployment. We want High Availability/redundancy. We've been told we must deploy UCM, with its primary security server and deployment...

I've built dual-boot systems in the past using a second partition on a drive by just booting from another XP install disk, but this time I started without the intent of making my system dual-boot and have changed my mind. I have a system running XP that is made up of three hard drives; c, d...

Just curious about how many of you have upgraded/migrated an Option 61C (or other large system for that matter) to a CS1000E. We're in the middle of such an upgrade, converting eight IPEs to media gateways off a CS1000E run by six CPPMs inside three MG1010 cabinets; two cores, and four...

Hey guys, I have setup a website in IIS and it is the only one. When I try to access it from the public side it asks for a username and password. How can I get it to not ask for it? Thanks

I've configured the above phone (192.168.6.90) and am able to make calls to DNs on my CS1K running 5.50J. I can't call from my CS1K to the Siemens phone. I've included two wireshark traces. The first shows the successful call. The second shows a failed call. I have tweaked and tweaked but seem...

A while back I found a tip that I use all the time with explorer.exe shortcuts. In the properties - Target I add /n, /e, /select, C:\ (or whatever path I want) I'm curious what those attributes are and where I can find a comprehensive list of all attributes that can be used there along with...

NEC article 800.90(2) among other things says: Fused-type primary protectors shall consist of an arrester connected between each line conductor and ground, a fuse in series with each line conductor, and an appropriate mounting arrangement. This sounds very descriptive of the typical 5-pin...

I built an agent incorrectly and took it out to rebuild. Before taking it out I issued the following command in LD 48: dacr agt l s c u Now that I've rebuilt the agent correctly I can't recall how to re-acquire the agent. It stats enabled an logged in and the port is enabled in CallPilot...

I'm looking for a product that will allow me to catch SNMP traps to a server running W2K3 Server, and if needed open or close a set of contacts that can be used to activate an alarm. I'm envisioning a USB device that will provide the contact interface. Does anyone have any experience with a...

Hello, What do I look for to know my newly purchased 2811 has CME on it? It hasn't arrived yet so I can't provide any printouts. I'm new to Cisco VoIP and can't seem to find anything on the Cisco site confirming what it takes to have CME on a router, other than minimum requirements. I don't...