Search results for query: *

Hi- Just a question on how Meet-Me-Bridge for UCM works. The Cisco doc states that: "For the Cisco Software Conference Bridge—The maximum number of audio streams is 128. With 128 streams, a software conference media resource can handle 128 users in a single conference, or the software...

Hi- Our company is planning to upgrade our Fast-E to a new Gig-E Internet connection. I'm currently in a look-out for a Layer 3 switch to replace the current 3750. What do you guys suggest? I won't be running any fancy routing such as BGP so no particular need for higher memory models. I do...

Hello- I've upgraded my switch firmware from IPBase to IPSevices. The download works well but upon boot-up, it will look for the old IOS first and display this error: Error loading "flash:/c3750-ipbasek9-mz.122-50.SE5/c3750-ipbasek9-mz.122-50.SE5. bin" It will still load using the new IOS...

Hi- I was able to successfully set-up point-to-point L2L VPN using Cisco routers. Now my problem is I want to put up an ACL on the WAN interface (facing the Internet) so that it will deny everything else except my L2L VPN tunnel. Any ideas on how my ACL should look like? Is it ok to block...

We are on the market for WAN Load Balancers, primarily to provide 100% uptime to our Data Center. We have two Fast-E from two different carriers and we want automatic fail-over in case one fails. What brand is most common? RADWARE Linkproof? Cisco? Thanks.

Hi- We have our Prologix connected to our ECAS server for some time using a serial cable. Yesterday, ECAS stop receiving data from the PBX. I'm not sure if it's the link or the ECAS server COM port that is faulty. Which command on the PBX will show the status of this CDR link? I haven't done...

Hi- I canceled my maintenance agreement with Avaya and switch to a local provider with a lower monthly cost. I didn't notice this initially after the switch (maybe after a month or so) but for some reasons, some of my admin commands such as busyout or release trunks are no longer there. I...

Hello- Our incoming calls are not going in to the voicemail. At the same time, when I call the hunt group to check my voicemail, I only get a busy tone. I checked the analog ports facing it and they are all "on-hook" and when I call them directly (not through the hunt group) they will just ring...

Hi- I'm trying to install a Cisco IP Gateway to a satellite office of ours that is using BCM50 PBX. The vendor added new analog line, assign them extension (eg 211) to connect to the FXO port of the IP Gateway. Our set-up is if anyone from this branch office wants to call the Main, he just...

Hi- I have a 1721 with an E1 WIC and I'm trying to match my provider's setting. Their router facing mine is using this: MTU 1500 bytes, BW 1984 Kbit, DLY 20000 usec, rely 246/255, load 1/255 Encapsulation HDLC, crc 16, loopback not set I was able to copy this setting except for the "CRC 16"...

Hi all- I'm trying to connect a Tenor DX back-to-back to an Avaya Prologix using the ffg settings (below) but I can't get the D channel to turn-up. Anything I'm missing here? My Tenor DX's ISDN is set-up like this: Protocol= PRI5ESS D-channel= Channel 24 Orientation = Network/Master T1, B8ZS...

Hi- Just a bit confused: when do you need to use a 120A CSU on a TN464F? I have noticed on this client Prologic that for some, they have their TN464s connected to a 120A CSU but some do not. I was thinking that they have an external CSU/DSU but none. Any ideas? Those with 120A are connected to...

Hi- I have this device that we're trying to get in to. We neither have its console nor telnet password. I tried to mirror the port on the switch and hoping it will send-out Broadcast and show on my Wireshark its IP add. But we can't get any even if we recycle the power. Any suggestion...

Hi- I'm trying this config on my lab. I have a 2801 router that is connected to the internet (via FE0/0). Now I have a L2 switch connected to this router's FE0/1 with IP add 192.168.1.1 for use by VLAN1. On the same interface, I added a secondary IP add 192.168.2.1 for VLAN2. Will there be a...

Just wandering if there's a possible way to check which host (or IP address) these output drops is coming from? Input queue: 0/75/285/0 (size/max/drops/flushes); Total output drops: 5316 I can run a Kiwi syslog server if needed. Thanks.

Hi- I have a user that's requesting 16 public IP adds for hosts. As you know, the closest we can get is a /27 which has 30 hosts. What's the best way to limit them to 16? Here's what I'm supposed to configure my router to send him a /27: ip route xx.xx.xx.xx 255.255.255.224 1.2.3.4 What do...

Hi- Assuming 1.1.1.0 and 2.2.2.0 are all public routable IP adds. Is this type of IPSec VPN secure enough? PC -------- router --- IPSec VPN (WWW) --- router ------- PC 1.1.1.2 1.1.1.1 2.2.2.1 2.2.2.2 Some in here says it is not since the PCs are using public...

Hi- I'm sure somebody here has done this before. We're a start-up company but we get tired of changing our IP adds each time we replace our Internet provider. Any ideas where to start? We're also thinking of getting our own ASN from ARIN. Thanks.

Hi- I'm sure somebody here has done this before. We're a start-up company but we get tired of changing our IP adds each time we replace our Internet provider. Any ideas where to start? We're also thinking of getting our own ASN from ARIN. Thanks.

Anyone have any ideas why I can't a access this router on Telnet and SSH using Putty? Thanks, Newbie line 194 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh line vty 0 4 login local transport...