Search results for query: *

I have a QPC 414 card that is currently configured with a QPC 720 card for a t1 circuit on its first port. There is nothing programmed on the second port of the QPC 414 card. I am planning to replace the QPC 414 card with a NT5D12 Dual port card. What programming changes do I have to perform to...

Will the Nortel line side T1 card operate in the wall mount fiber remote cabinet from an Option 81C? If so, what is the card part number?

Did Nortel make a line side T1 card that would operate in the Option 11 type cabinets?

Will setting a PBX up with 2 customers instead of 1 allow you to prevent calls from certain DN's on customer 0 from calling dn's on customer 1? If so, do you have to build a seperate data block in load 15 for each of the customers? I only want the second customer to be able to call another DN...

Is there a cordless digital telephone that will work on the M2616 port.

Does Avaya have anything that would work similar to Merdian Mail Express messaging. If I have a answered caller on my phone I would like to be able to send the caller directly to a voicemail box for purposes of leaving a message.

Nortel has a way to look at the inbound and outbound messaging on the d-channel on a PRI. Does Avaya have a way to do the same on their systems?

Does anyone have a source for Avaya Visio templates that includes the S8800 server?

I want to select line instead of Line Pool for outdial from a CP mailbox for remote notification . What should my digit stream look like that is outpulsed. Specifically what do I enter to access a particular line?

Do you have to set up at least 1 trunk in a Line Pool to do remote notification to a pager? My system is set up as a squared arrangement and currently I don't any line pools.

We have a 4 node Meridian Mail 12 modular options voicemail system operating with a Nortel Option 61C. Sometime ago we begin to have a problem with Node 3. we would get complaints that some users were unable to access their voicemail boxes. Upon investigation we would find that the hard drive on...

We have replaced about all the parts you can replace on an Option 11 Meridian Mail Rel. 12 system. The AML link will drop out and it cannot be re-established until the MM is powered off and back on. When found down the MM green light will be flashing off and on. Once the MM is power cycled the...

Does the NT5d03FB processor card for an Option 61C have a security device? If so where is it located?

We have a menu(Call Pilot) on the incoming lines(MICS) setup with Select 1 for Sales, Select 2 for Technical support and so on. When you select 1 the call should transfer to 221 and then to 222 and then to 223. What is happening is that the caller will hear 4 rings and the call will disconnect...

On a Meridian 1 in Load 16 when programming the route data block for a PRI ,for prompt DSEL what determines if VOD or 3VCE is used as a response?

When dial 0 is dialed from any voicemail box, the greeting of the mailbox is replayed. Is there a way to to send the calls to the Attendant number or the General Delivery mailbox when 0 is dialed?

I have a Norstar with Startalk flash that is setup for calls to be answered by an AA. The Startalk Flash was recently replaced. When the call rings the telephone from the auto attendant,it is forwarded on ring no answer to the voice mail box associated with the dialed extension. When the...

What DS trunk part number will work in the expansion trunk module. We are running 7.1 software on the main cabinet.

I have a PRI with DID service inbound. Is it possible to block some of the outgoing telephone numbers from being sent out when an outgoing call is placed? The majority of the people in the office are ok with their number being sent out but I have a couple of managers who want their number blocked.

How long can I take the power off of a MICS and CP 100 before I lose the programming?