Search results for query: *

I have a user that needs to send udp info thru the firewall to an internal server He is trying to send via udp://38.100.31.xxx:20500 which should go to internal server 192.168.30.yy which is 2008R2 with firewall turned off The packets never get thru On the ASA I have the following setup for...

I am trying to enable and tunnel RDP on 3389 thru ssh to a server on our dmz. I am able to ssh and run commands and am able to browse web sites on the DMZ from our LAN. Any ideas?

I have a app running on an 2003 IIS box. There are other sites running on port 80 with no problem The application that I am having problems with is running on port 8080 on the same IIS server It is running internally on port 80 with an IP address of 192.168.30.30 and has a index page that...

I have created a rule that should open an ip adress on the friewall to an internal server, Internally the web server works fine, externall no connect by IP. Here is the rule access-list acl_out permit tcp any host 66.173.204.217 eq www static (inside,outside) 66.173.204.217 192.168.30.90...

We have noticed a real slow internet onnection when downloading. We ran speed tests and we get 1447 up and 600 down. We have a CISCO 1760 router and a Cisco Pix 515e.I have checked the speed and duplex on both the router and PIX and they are the same. What else should i check?

I have WiFi users using a access point on our DMZ. The users are stating they cannot access our web site or sharepoint portal on the internal network. They can access the sites if off site. What rules or access lists need to be setup for this configuration.

I wish to setup accounting on our pix 515e firewall. We are running 6.3(3). What is the the proper aaa accounting command to get full logging to show in the ISA logs. Listed below is the aaa section on the PIX aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server...

I notice that when viewing my IAS logs that my start time and date is the same as the stop time and date and does not show any IP information about the user. I have checked my IAS server configuration all settings are correct on the 2003 iAS server.

My secondary dns providor gave me a ACL list for my nameserver and pix. It shows 205.210.42.0/24 When I enter network-object host 205.210.42.0/24 it tells me invalid address. What is the way to enter this range without using each address

I have an exchange server located at 66.173.204.zzz....I have added the following lines to the pix but get a refushed connection, when connecting to IMAP froma remote location..OWA works fine. web sites work fine access-list acl_out permit any host 66.173.204.zzz eq imap4 access-list...

I have an internal ftp site at 192.168.30.20 and i am trying to reach it from outside locations at ftp//66.x.x.213. I have a web site already working at this location and is going through a pix 515e. What do I need to add to the pix to allow this connection, or what have I not configured...

I have an ftp and www server setup internally at 192.168.30.20. The www server works fine from the outside world thru the PIX. I have not been able to get the ftp to work from the outside.I have attached my running-config PIX Version 6.3(3) interface ethernet0 100full interface ethernet1...

I have a web site published and it works fine on the internal network. When trying to view it from the internet at a certain IP address I get a Http Authenication box being displayed. I have a CISCO PIX 515E. There was an old site previously published with the same internal and external IP addresses

I am a newbie with CISCO 515e. I just came into the location, and there is no documentation. I am able to connet via consle cable but I am unable to conect to pdm via https. I have enclosed areas of the config and am tring to access https://192.168.40.19 as the inside IP. pdm location...