Search results for query: *

Merlin Magix, with a 4424 set, with a headset, every time headset button is activated, when call comes in , you do not see caller id on the phone until you answer the call. when you remove the headset button, it works fine.

if you change the description of a node, is it service affecting?

I have a client which mostly has 4620's. Now the sets i am getting for repiars & adds are 4621's, i do not want the 4621's to stand out with the backlight on. i know of the MUTE off # command to turn off the light but it comes right back on. is there a command or a change in the 46xx txt to turn...

How can you tell if the Intuity has the DST patch? i figure going into software management, then intuity software, but what do i look for. i am on R5.1.53, i cant remember if my team had Avaya download the patch earlier this year.

in an Octel 250, how would i get a report similar to a list subsciber in an Intuity?

My client has a new NTP server which they would like me to sync to, if i go into the configure sever menu, then configure one service, then put the new IP address, will this cause the server to reboot? is it service affecting at all.

Is there anyway to not hear the extension or name of the covering extension? i would rather it just ring.

weird issue here. i have a g350 gateway of which i can telnet into, autosat, login to the g350, but i cant access the web interface for it using the login & password credentils of the 8700. the files sync ok because i can see it using the list sur. so why cant i login? running version...

i have a G3V6r (i know, i know), i am in the process of cleaning it up so i can move people over to a new PBX. My question is this, when i attempt to change adjunts names to remove 2 of the entries i get an error: USER DEFINED ADJUNCT NAMES AUDIX...

Have any of you noticed that when trying to download g350_mgp_sw-26.33.0 (or whatever the newest fw is) for an MM711 h30, that it will not take via the web upgrade tool.

all, below is my present procedure & configuration for remote access, back ups & maint. i have remote sites (NY, CA, MA) that are a mix of g350 & g700's. today i dial a CO lines then ras in. one there i open my emulator to access the "PBX" gui. to do a back up, i dial in the same way, but...

where do i administer so that the actual IP address is shown when i do a ststus login, instead of 127.0.0.1, this only started after i upgraded to 4.0 Login Profile User's Address Active Command Session soft 23 127.0.0.1...

We have a early verison of the partner 7.0, what is the procedure to upgrade to the latest release. i have the latest pcm card.

all, i am trying to use video conf off a G700, i am trying to send the call out the local pri instead of my main server. below is the error i get denial event 1367: BCC incompatibility D1=0x87004a D2=0x22b6 any ideas? running CM4.0

All, is there anyway to tell from the SAT via status station or another command, that will tell you if a phone is a remote VPN set or if its a local set?

Would anyone happen to know where i can find a doc that describes that alarms that the Octel has? i am being asked to monitor a few octels so we can remove our contract with someone else, getting the alarms is not an issue, but i would like a refernce to look at when i respond to them.

Hey folks, would any of you happen to know where i can download or buy a configurator for when my sales folks ask me to design a new solution. i would like to have something where i can input how many phones, t-1's, clans, medpros, etc... & it spits out what wold need, g250, 350, 700 etc...

all, after upgrading to CM 4.0 i noticed that when i status logins, the users address no longer shows the IP address of the PC telnetted into the box. it only shows 127.0.0.1, is this something my IT has restricted or is it something on the CM?

Have any of you seen where the 96XX cannot transfer to an X ported L/A?, unless you put a port on it.

Hey All, ok, so i upgraded to R4.0. but my login permissions did not transfer over, no big deal, but i'm having an issue trying to figure out how to convert whay i had under the old login permissions, to the new user-profile. i looked in the 4.0 doc, but it's only accurate up to Feb 07 &...