Search results for query: *

Hi Guys, Is there an official list of the Feature Codes for DISA? I have configured all the parameters and when I dial in, I get a dial tone but not sure which feature code to enter. The call drops as soon as I enter more than two (2) values. From ALEX, its like this... DISA number DT * FC *...

Hi Guys, I just installed a voicemail system at the office and I'd like to test it out. Currently, the employees are programming an external call diversion from their individual extension to their mobile number. How do I disable this feature for some select employees? Thanks

Hi, I'm trying to install a few softphones on our office PC's. I have properly installed an IPLU as a gatekeeper and I've set an IP extension (DIR=220) with password = test. I have all the valid licenses for VoIP on the system. I've tried SJPhone but I get a login reject or something like that...

Hi, I recently changed the default password of MDUSER (default user) but now, when I try to login with SSSSSS; to get to the username/password prompt, I get this message: LOGON REJECT SYSTEM PROTECTION ON How would I disable the SYSTEM PROTECTION to let me log in? Do I just wait for the...

Hi Guys, I've been trying over the last couple days to get my absent operator to divert but still no success. PELPI, CDINI commands dont work and OPADC. Any suggestion guys? I dont think a *21*ext# works either... Thanks

Hi Guys, I recently configured a voicemail system for our mx-one but the issue is that I would like a call to be routed to additional extensions prior to heading to the voicemail huntgroup. The Voicemail Huntgroup = 270 and all calls are currently set to divert to that position if unanswered...

Hey Guys, I'm in the final stages of installing a voicemail system in our PBX. I have setup a voicemail huntgroup that calls divert when there is no answer. I have changed the SYTDS parameters to extend the Call Divert Long and Short times. So far, calls to the PBX from outside (external) take...

Hi Guys, I am in the process of integrating a Diavox Voicemail System with our MD110 BC12 PBX (TCP/IP Integration). The voicemail card is connected to an analog extension (238) and I would like for calls (extensions 200-215) to be diverted to this extension after 7 or so seconds of ringing...

Hi Guys, I recently installed a Diavox Voicemail Server (TCP/IP Integration) but I seem to be getting this error/alarm when the PBX wants to connect to the Voicemail Server. 345 2 1 INFORMATION COMPUTER, FAULTY COMMUNICATION CHANNEL Also, I cant see anything on the server side...

Hi guys, Got a quick question. Is is possible to dial into a specific extension on the PBX from any location and receive and external dial tone to another route on the PBX? I would like to cut some long distance costs and want to explore this option. I've done some research on Remote Extensions...

Hi Guys, I'm trying to setup a H.323 Trunk between point A (IPLU with address 192.168.1.1) and point B (IPLU with address 192.168.1.2) these devices can ping each other the network so there are no issues there. I have also purchased the following licenses: 1 FAL104707 MD IP teleph interf SW...

Is it possible to have a QSIG (or any type of point-to-point) connection between two MX-One PBX's without some type of VoIP router in between. I am missing something here? I have my network equipment (CSU/DSU) setup as a framed E1 link. That is Timeslots 1-15&17-31 are transported as voice data...

Hi, I'm trying to configure a QSIG trunk between a long distance point to point E1 line we have leased. We are currently getting framing/timing errors on the link. What would be the typical paramters in ROCAI and RODAI for this type of connection. Assuming one is the master and the other...

Hey guys, I've looked through the MD110 ALEX and I still cant figure out the function of a LOG2 board. I know it has something to do with the LPU but how is it connected and what is its purpose? Thanks

I've got ISDN service coming into a TLU76 card an there are currently no framing/data link alarm. I attempt to make a call to the PSTN but I get an immediate disconnect. Please review the trace below and let me know if you have any opinions. Also, when I attempt to dial into the PBX, I get no...

I have a leased E1 circuit from point A to point B. I want to be able to carry both voice and data on this ciruit. I have and MX-One LIM at each location with 2 TLU76 cards each. One TLU76 to the public PSTN and the other to a perhaps "zero-padded" E1 ((E1)/2-->due to data on the other half)...

I currently have 3 leased E1 lines from the Point A to Point B. We have an MX-One's (1 LIM) at each location. Is there an additional plug-in unit (other than TLU76) needed to allow for a point to point connection between the sites? Any help would be appreciated!

We currently have an exchange server sitting behind out PIX 515E and we are unable to receive email. Looking at the logs it says the following: Outbound email works just fine. TCP request discarded from xx.x.x.91/60772 to outside:x5.xx2.xx.xx6/25 Any help on this would be appreciated.. here...

We attempted to make a console connection from our PC to our Cisco PIX 501 firewall to interrogate connection settings and the PIX rebooted immediately and has been rebooting ever since!! here are the message I get... Reading 1962496 bytes of image from flash...

Hi, I have a lab setup with an MD110 connected to a simulated PSTN network via a DSS1 link. The PSTN is currently configured for D.I.D only (to MD110) for testing purposes. We have initaited a signalling connection between the equipment, the only issue that I have is creating an extension. I...